
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X475-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 475mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X475-100 is a double-acting ISO 15552 profile cylinder featuring a rear mechanical adjuster that allows you to trim the nominal 475 mm stroke back by up to 100 mm. This creates a highly flexible 375-475 mm usable travel window, letting you dial in exact end positions during commissioning without swapping out the barrel or adding external stops.
This variant uses a standard carbon steel piston rod with M16x1.5 threading and PT tapered port threads. The extruded aluminum barrel includes sensor grooves on both sides for direct mounting of CMSE reed or DMSE electronic switches if position feedback is later required. The rear adjuster functions purely as a travel stop to set the retract position, working alongside the standard adjustable air cushions at both ends to decelerate the load. It does not lock or hold the load pneumatically without live air pressure.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X475-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly fine-tune the 375-475 mm retract end-stop during product family changeovers on a packaging line, eliminating the need to physically swap cylinders or reposition hard stops.
Dial in the exact retraction point for a dispensing head, using the 100 mm adjustment window to accommodate different container sizes without reprogramming the motion controller.
Trim back the nominal 475 mm stroke during initial machine commissioning to perfectly time a sequencing action, absorbing mechanical tolerances via the rear stopper screw.
If your setup demands higher thrust, stepping up to the 63 mm bore provides 1559 N at the same pressure. The SAIJ50X475-100 is specifically selected over a fixed-stroke SAI model when machine changeovers or product size variations require frequent, fine-tuned adjustments to the retract position. Because the nominal stroke is 475 mm, the M16x1.5 rod is relatively long; for any application exceeding 300 mm of travel, you should use an external guide rail to prevent side-loading and premature seal wear.
For ISO 15552 dimensionally interchangeable replacements, match the 50 mm bore, 475 mm nominal stroke, 100 mm adjustment range, PT port threads, and carbon steel rod. Note that the SAIJ mounting set is limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR mounting styles. Since this model lacks the -S magnet suffix, it does not support CMSE or DMSE sensors out of the box. Remember that the rear adjuster is a stop, not a lock; if you need true load-holding without continuous air pressure, consider the SAIL or BSAI series instead.
Quick checklist
At the maximum 1.0 MPa pressure, it delivers up to 200 kgf.
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective travel from the 475 mm nominal stroke down to as little as 375 mm. It sets the end position but does not hold the load without live air pressure; for load-holding, use a SAIL or BSAI cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.