
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X600-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 600mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X600-30 is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, designed to provide precise end-position tuning without the need for external stops. It features a 600 mm nominal stroke that can be dialed back by up to 30 mm, creating a 570-600 mm usable travel window ideal for product changeovers.
This extruded aluminum profile cylinder includes adjustable air cushions at both ends to manage impact deceleration. It is important to note that the rear adjuster acts strictly as a travel stop and does not hold the load without live air pressure. For load-holding requirements, consider the SAIL or BSAI series. The barrel incorporates sensor grooves on both sides, allowing for direct mounting of CMSE reed and DMSE solid-state switches if a magnet is specified later.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X600-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 570-600 mm retract position during product size changes without physically swapping the cylinder or adding mechanical shims.
Adjust the exact stroke endpoint on the fly to accommodate different package lengths arriving on a sorting line.
Fine-tune the final 30 mm of the 600 mm travel to achieve precise contact depth during assembly commissioning.
If your setup demands less force, stepping down to a 40 mm bore yields 628 N, whereas moving up to a 63 mm bore provides 1559 N. The adjustable 30 mm window on this 600 mm stroke allows operators to fine-tune the retract position during commissioning, eliminating the need to physically swap a fixed-stroke SAI cylinder.
When replacing an ISO 15552 cylinder, match the 50 mm bore, 600 mm stroke, 30 mm adjustment, PT tapered port thread, and the specific mounting accessory. SAIJ supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR options. Because the stroke is 600 mm, the extended 16 mm rod and M12x1.25 thread can carry significant side loads; an external guide rail is recommended to prevent rod bending and premature seal wear.
Quick checklist
If operated at 0.7 MPa, the push force increases to 1374 N.
The rear adjuster screw acts as a mechanical stop that shortens the effective travel. For this SAIJ50X600-30, you can trim the 600 mm stroke back by up to 30 mm, giving a usable travel window of 570-600 mm. It does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.