
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X700-100S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 700mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X700-100-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It features a 700mm nominal stroke that can be fine-tuned backward by up to 100mm, yielding a precise 600-700mm usable travel window for exact end-position setting.
This model uses a PT tapered port thread (G1/4) and relies on variable air cushions at both ends to decelerate the load. The rear adjuster acts purely as a mechanical stop to set the travel limit and does not hold the load without live air pressure. For load-holding requirements without continuous air, an external pilot-operated check valve or a related SAIL pneumatic lock cylinder is required.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X700-100S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial the travel back from 700mm to 600mm via the rear screw to accommodate varying package lengths on a packaging line without changing cylinders.
Fine-tune the exact end-of-stroke position during initial commissioning to perfect a press or indexing motion without adding bulky external stoppers.
Establish precise mechanical limits for diverter arms on a conveyor system, ensuring the rear stopper absorbs the final impact while the air cushions manage deceleration.
If your setup needs less force, stepping down to a 40mm bore provides 628N at 0.5MPa; if higher thrust is needed, moving up to a 63mm bore yields 1559N at 0.5MPa. The adjustable stroke is selected over a fixed SAI cylinder when commissioning requires fine-tuning without swapping physical hardware.
When replacing this ISO 15552 cylinder, match the 50mm bore, 700mm nominal stroke, 100mm adjustment range, PT G1/4 port, and the -S magnet option. Because the stroke is 700mm, the 16mm rod diameter and long unsupported travel increase the risk of side-load damage; an external guide rail is strongly recommended to prevent premature seal wear. The SAIJ mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2, deliberately omitting FB, CA, CB, and CR brackets.
Quick checklist
At 0.7MPa, the push force increases to 1374N.
The rear adjuster screw acts as a mechanical stop that shortens the effective travel. For this SAIJ50X700-100-S, you can trim the 700mm stroke back by up to 100mm, creating a 600-700mm usable travel window. It only sets the end position and does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.