
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X80-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 80mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X80-75-S is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. Equipped with a -S magnet, it integrates seamlessly with AirTAC CMSE reed and DMSE solid-state sensors via the dual-side barrel grooves.
This model provides an expansive usable travel window of 5-80 mm, allowing you to dial back the nominal 80 mm stroke by up to 75 mm. The rear stopper mechanism enables precise end-position tuning at commissioning or during product changeover without adding external stops. Note that the adjuster acts strictly as a travel stop and deceleration aid alongside the 30 mm air cushions, not as a load-holding lock.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X80-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 80 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end-stop position for different part lengths on a single machine bed without physically replacing the actuator.
Fine-tune the retract end-position during initial setup to achieve perfect alignment and crush tolerances without external spacers.
Adjust the travel window on the fly for assembly lines processing multiple product sizes, using the integrated -S magnet for position confirmation.
Choose this adjustable-stroke cylinder when your fixture requires variable end-stops on the fly, avoiding the need to swap out a fixed-stroke SAI cylinder for every product variant. If your setup demands higher thrust, stepping up to a 63 mm bore yields 1559N at 0.5 MPa, whereas dropping to a 40 mm bore reduces thrust to 628N. Because the 80 mm stroke is well below the 300 mm threshold, side-load concerns are minimal, though the M16x1.5 rod still handles standard lateral loads effectively.
For an exact ISO 15552 dimensional replacement, match the 50 mm bore, 80 mm stroke, 75 mm adjustment range, PT tapered port threads, and the -S magnet option. The SAIJ mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2, deliberately omitting FB, CA, CB, and CR brackets. If your application requires the load to be held without live air pressure, this cylinder will not suffice; you should consider the SAIL air-released lock or BSAI clamp-lock alternatives instead.
Quick checklist
It operates at speeds between 30 and 800 mm/s.
The rear adjuster screw allows you to shorten the effective stroke by up to 75 mm, providing a usable travel window of 5 to 80 mm for precise end-position tuning without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.