
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X800-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 800mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X800-30 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a nominal 800 mm travel that can be dialed back by up to 30 mm, yielding a precise 770-800 mm usable window for fine-tuning the retract end position during commissioning.
Because the stroke extends to 800 mm, the 20 mm rod diameter and M16x1.5 rod thread provide robust support, though an external guide is strongly recommended to prevent excessive side-loading on the long unsupported length. The extruded aluminum barrel includes sensor grooves on both sides, allowing you to add CMSE reed or DMSE electronic switches if position feedback is later required.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X800-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 770-800 mm retract position on packaging lines when handling different carton sizes, avoiding the need to physically swap out long-stroke actuators.
Fine-tune the end stop on extended-trroke material handling or machining tasks where a 30 mm trim perfectly aligns the tooling without external shims.
Adjust the stroke window during initial commissioning of automated assembly equipment to perfectly seat components, compensating for mechanical tolerance stack-up.
Choose this 50 mm bore when an application demands moderate thrust—stepping down to a 40 mm bore drops the 0.5 MPa push force to 628 N, while stepping up to a 63 mm bore increases it to 1559 N. The adjustable rear stopper is ideal for product changeovers on a line, letting you shift the end-of-stroke position without swapping the cylinder or adding external mechanical stops. It operates at speeds of 30-800 mm/s.
When replacing an ISO 15552 cylinder, match the 50 mm bore, 800 mm stroke, PT port threads, and the desired mounting accessory from the SAIJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that the rear adjuster acts only as a travel stop and does not hold the load without live air; for dead-air load holding, consider an AirTAC SAIL or BSAI variant. Furthermore, the variable air cushions at both ends manage deceleration but are not braking mechanisms.
Quick checklist
At the maximum 1.0 MPa pressure, it achieves a peak thrust of 200 kgf.
The rear adjuster screw allows you to shorten the effective stroke by up to 30 mm, creating a 770-800 mm travel window. This stopper sets the retract end position but does not lock the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.