
The AirTAC SAIJ50 Adjustable Cylinder SAIJ50X95-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø50mm bore and 95mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ50X95-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. With a 95mm nominal stroke and a 75mm adjustment range, it provides a wide usable travel window of 20 to 95mm. This allows you to fine-tune the retract end position at commissioning without adding external stops.
The extruded aluminum barrel includes sensor grooves on both sides for straightforward switch placement. Unlike fixed-stroke SAI units, this model uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. The 20mm diameter carbon steel rod and M16x1.5 thread provide strong resistance to side loads, while the PT tapered port threads ensure a reliable pneumatic seal.
| Model | Airtac SAIJ50 Adjustable Cylinder SAIJ50X95-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 95 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 825 N | 825 N |
| 0.7 MPa | 1155 N | — |
| Max (@1.0 MPa) | 168 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×95 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract distance between 20 and 95mm during machine commissioning to perfectly align pressing or clamping forces without swapping out physical hardware.
Adapt a single actuator station on a packaging line to handle multiple product lengths rapidly by adjusting the rear stopper screw rather than repositioning the entire cylinder.
Select this 50mm bore actuator when your application requires variable end-stops for frequent product changeovers, as it allows you to trim the travel back by up to 75mm on the fly. If your setup needs less push force, stepping down to a 40mm bore yields 628N at 0.5MPa; for heavier payloads, moving up to a 63mm bore provides 1559N. Because the stroke is under 300mm, side-load stress on the 20mm rod is moderate, though external guides are still recommended for heavy off-center loads.
This cylinder is dimensionally interchangeable per ISO 15552, making it a direct for standard 50mm profile cylinder footprints. To match this exact configuration, specify the 95mm stroke, 75mm adjustment, PT port threads, carbon steel rod, and no magnet. Remember that the rear adjuster is a travel stop, not a locking device; the cylinder cannot hold a load without live air pressure. For true pneumatic load-holding, consider the AirTAC SAIL or BSAI series instead.
Quick checklist
It operates at pressures from 0.15 to 1.0MPa, reaches a maximum of 200 kgf at 1.0MPa, and runs at speeds between 30 and 800mm/s.
The rear stopper screw allows you to shorten the 95mm nominal stroke by up to 75mm, creating a usable travel window of 20 to 95mm. This adjuster acts as a physical stop to set the retract end position and does not lock the load in place without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.