Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10
The AirTAC Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 280mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke280 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10
The AirTAC SAIJ80X280-10 is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, delivering a robust 2513N push force at 0.5 MPa. It features a 25mm carbon steel rod and a PT G3/8 port. By integrating a rear stopper screw, this actuator provides a usable travel window of 270-280mm, enabling precise end-position tuning during commissioning without swapping out the entire unit.
This model utilizes an extruded aluminum barrel with dual sensor grooves, accepting CMSE reed or DMSE electronic switches if a magnet is added later. The rod is constructed from SUS420J2 stainless steel (material code A) for enhanced durability against moisture. It supports a speed range of 30-800mm/s and relies on adjustable air cushions at both ends to decelerate the load smoothly.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10 Technical Specifications
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10 Is Used
Machine Changeover
Dial in the 270-280mm travel window during product size changes to set new end positions rapidly without adding external physical stops.
Diverting Mechanism
Provides 2513N of push force at 0.5 MPa to actuate routing gates, with the 10mm trim allowing precise alignment of diverters.
Assembly Press
Uses the rear stopper to set a hard mechanical limit for pressing operations, while the SUS420J2 stainless rod resists minor environmental moisture.
Is the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10 the Right Cylinder?
Choose this 80mm bore actuator when an application requires moderate thrust and on-the-fly stroke trimming; if you need less force, the 63mm bore provides 1559N at 0.5 MPa, while stepping up to 100mm yields 3927N. The 10mm adjustment range is ideal for dialing in a final end-stop during product changeovers rather than relying on a fixed-stroke SAI cylinder. To match your exact ISO 15552 replacement requirements, confirm the 280mm stroke, 10mm adjuster, PT G3/8 port, and preferred mounting bracket (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
Because the nominal stroke is 280mm, ensure adequate external guiding to support the load and prevent excessive side-loading on the rod. Remember that the rear adjuster and air cushions act only as travel stops and deceleration devices; they do not hold the load without live air pressure. For true load-holding, consider an external rod lock or the AirTAC SAIL series.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10 FAQ
At 0.5 MPa operating pressure, this 80mm bore cylinder provides a push force of 2513N and a pull force of 2268N. At 0.7 MPa, the push force increases to 3518N.
The rear adjuster screw allows you to shorten the effective travel from the nominal 280mm down to 270mm, creating a 270-280mm usable window. This stopper fine-tunes the end position but does not lock the load without continuous air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAIJ80 Adjustable Cylinder SAIJ80AX280-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.