Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S
The AirTAC SAIJ80 Adjustable Cylinder SAIJ80AX325-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 325mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ80 mm
- Stroke325 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S
The AirTAC SAIJ80X325-30-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a 295-325 mm usable travel window by allowing you to dial back the 325 mm nominal stroke by up to 30 mm.
Equipped with a SUS420J2 stainless steel rod and a PT tapered port thread (G3/8), it integrates seamlessly with existing setups. The extruded aluminum barrel includes sensor grooves on both sides, and the integrated -S magnet supports AirTAC CMSE reed and DMSE electronic solid-state switches for precise position feedback.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S Technical Specifications
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S Is Used
Machine Changeover
Dial in the exact end-stop during product size transitions on a packaging line without physically replacing the actuator.
Commissioning Fine-Tune
Trim the 325 mm stroke by up to 30 mm to perfectly align tooling interfaces during initial equipment setup.
Variable End Positioning
Adjust the retract stroke length on the fly to accommodate varying material thicknesses in pressing applications.
Is the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S the Right Cylinder?
The 30 mm rear adjuster is ideal for fine-tuning end positions during machine commissioning or product changeovers without swapping cylinders or adding external stops. Remember that the rear adjuster acts only as a travel stop; it does not hold the load without live air. For load-holding without pneumatic pressure, consider the SAIL or BSAI series.
Because the 325 mm stroke is relatively long, an external guide is recommended to prevent excessive side-loading on the rod. As a dimensionally interchangeable ISO 15552 cylinder, it uses a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). Operating speed ranges from 30-800 mm/s.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S FAQ
At the maximum operating pressure of 1.0 MPa, it delivers up to 513 kgf.
The rear adjuster screw allows you to shorten the effective stroke by up to 30 mm, creating a 295-325 mm usable travel window. It functions purely as a mechanical stop and does not lock or hold the load without live air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAIJ80 Adjustable Cylinder SAIJ80AX325-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.