Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30
The AirTAC SAIJ80 Adjustable Cylinder SAIJ80AX60-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 60mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ80 mm
- Stroke60 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30
The AirTAC SAIJ80X60-30 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to shorten the effective travel. With a 60mm nominal stroke and a 30mm adjustment screw, you get a highly flexible 30-60mm usable travel window for precise end-position tuning at commissioning. The extruded aluminum barrel includes sensor grooves on both sides for direct mounting of CMSE or DMSE switches. The rear adjuster acts purely as a mechanical stop to set the retract end position, meaning it does not hold the load without live air pressure. For load-holding requirements, consider the SAIL or BSAI series.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30 Technical Specifications
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30 Is Used
Machine Changeover
Dial in the 30-60mm travel window during product size changeovers to set new retract end positions without physically swapping the cylinder.
End-Position Tuning
Fine-tune the exact retract stroke limit during machine commissioning to compensate for mechanical tolerances in the fixture.
Variable End Stops
Use the rear adjuster screw to set different stroke limits for multiple operations running on the same 80mm bore pneumatic station.
Is the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30 the Right Cylinder?
If you need less force, stepping down to a 63mm bore yields 1559N, while moving up to a 100mm bore provides 3927N. The SAIJ80X60-30 is selected over a fixed SAI cylinder when you need to dial in a specific travel window between 30 and 60mm without adding external stops or swapping the cylinder during product changeovers.\n\nBecause the stroke is relatively short at 60mm, side-load stress on the 25mm rod is minimal, but an external guide is always recommended for heavy loads. This model uses a reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting FB, CA, CB, and CR brackets. It is dimensionally interchangeable per ISO 15552 mounting interfaces.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30 FAQ
At the maximum operating pressure of 1.0 MPa, it can deliver up to 513 kgf.
The rear adjuster screw lets you trim the 60mm nominal stroke back by up to 30mm, creating a usable travel window between 30mm and 60mm. The adjuster acts as a mechanical stop for the retract end and does not function as a lock to hold the load without live air.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAIJ80 Adjustable Cylinder SAIJ80AX60-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.