Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10
The AirTAC SAIJ80 Adjustable Cylinder SAIJ80AX75-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 75mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ80 mm
- Stroke75 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10
The AirTAC SAIJ80X75-10 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a nominal 75 mm stroke that can be fine-tuned down by up to 10 mm, creating a precise 65-75 mm usable travel window for exact end-position calibration.
This variant features a SUS420J2 stainless steel rod for enhanced corrosion resistance and utilizes a PT tapered port thread. The extruded aluminum barrel includes dual-side sensor grooves for mounting position switches. It supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options. The rear adjuster acts strictly as a mechanical stop to set the travel end and does not hold the load without live air pressure.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10 Technical Specifications
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10 Is Used
Machine Setup and Changeover
Dial in the exact 65-75 mm retract position during product size changes without physically swapping out cylinders or re-engineering external stopper blocks.
End-Position Tuning
Fine-tune the final retract distance by up to 10 mm during commissioning to accommodate mechanical tolerances and ensure precise tool alignment.
Is the Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10 the Right Cylinder?
If your thrust requirements are lower, stepping down to a 63 mm bore yields 1559 N at 0.5 MPa, whereas moving up to a 100 mm bore provides 3927 N. The adjustable stroke is ideal for machine setup and product changeovers, allowing you to dial in the exact retract position without swapping the cylinder or adding external stops.
Because the stroke is 75 mm, side-load risks are minimal, but always ensure proper rod alignment. If your process demands true load-holding without continuous live air, note that this cylinder's adjuster is a stop, not a lock; you should instead consider an AirTAC SAIL (air-released lock) or BSAI (clamp-lock) cylinder. For ISO 15552 dimensional interchangeability, match the 80 mm bore, 75 mm stroke, 10 mm adjustment, PT port thread, and your required mounting accessory.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10 FAQ
At 0.7 MPa, the push force increases to 3518 N.
The rear adjuster acts as a mechanical stop that allows you to shorten the nominal 75 mm stroke by up to 10 mm, providing an adjustable travel window of 65 to 75 mm. It sets the end position but does not lock or hold the load without live air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAIJ80 Adjustable Cylinder SAIJ80AX75-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.