Airtac SC50 Standard Cylinder SC50X410
The AirTAC SC50 Standard Cylinder SC50X410 is a genuine double-acting standard air cylinder with a Ø50mm bore and 410mm stroke, PT1/4 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
- BoreØ50 mm
- Stroke410 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 21 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SC50 Standard Cylinder SC50X410
The SC50X410 is a double-acting pneumatic cylinder from the AirTAC SC tie-rod series, delivering a push force of 982 N at 0.5 MPa and up to 1767 N at the maximum operating pressure of 0.9 MPa. With a 50 mm bore and a 410 mm stroke, this model uses a 20 mm diameter piston rod and PT1/4 ports, making it a robust mid-range actuator for industrial linear motion.
This cylinder features an adjustable air cushion (21 mm length) at both ends to decelerate the piston smoothly, reducing end-of-stroke impact. The body length A is 150 mm, giving a total extended length of approximately 560 mm. It operates on filtered air within a standard temperature range of -20 to +70 °C and is built for reliable, high-cycle performance in factory automation.
Airtac SC50 Standard Cylinder SC50X410 Technical Specifications
| Model | Airtac SC50 Standard Cylinder SC50X410 |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø50 mm |
| Stroke | 410 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (approx.) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SC50 Standard Cylinder SC50X410
| SC | Standard tie-rod cylinder series. |
|---|---|
| 50 | Bore size in mm. |
| ×410 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac SC50 Standard Cylinder SC50X410 Is Used
Material Transfer Gates
Actuates diverter gates on conveyor lines, using its 410 mm stroke to reliably push products between lanes in packaging and logistics hubs.
Press-Fit Assembly
Provides the controlled 982 N force at 0.5 MPa for pressing bearings, bushings, or dowel pins into housings in automated assembly cells.
Hopper Door Actuation
Opens and closes discharge doors on bulk material hoppers, leveraging the long 410 mm stroke for full gate travel in agricultural or processing equipment.
Is the Airtac SC50 Standard Cylinder SC50X410 the Right Cylinder?
Select the SC50X410 when your application requires a mid-range force of 982 N at 0.5 MPa. If you need a more compact actuator with lower force, consider stepping down to the SC40 bore, which provides 628 N at the same pressure. For higher thrust, the SC63 bore offers 1559 N. For this 410 mm stroke, ensure the rod is adequately supported against side loads; an external linear guide is recommended to prevent rod bending and premature bearing wear. When replacing an existing unit, match the 50 mm bore, 410 mm stroke, PT1/4 port thread, basic mounting configuration, and confirm if a magnet is required for sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SC50 Standard Cylinder SC50X410 FAQ
At the standard 0.5 MPa operating pressure, the push force is 982 N and the pull force is 825 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 1767 N. The theoretical maximum force at 1.0 MPa is 200 kgf.
No. The SC series is a double-acting cylinder and does not hold its position when air pressure is exhausted or the directional valve is centered. The piston will drift or drop under load. To hold a load safely, you must add an external mechanical lock, a rod brake, or a pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SC50 Standard Cylinder SC50X410
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.