The AirTAC AirTAC SDA16X45BH Compact Cylinder | 16mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø16mm bore and 45mm stroke, M5×0.8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA16X45BH is a double-acting, single-rod compact cylinder engineered for tight machinery footprints. Its riveted assembly minimizes axial mounting depth while delivering 100.5 N of push force and 86.4 N of pull force at 0.5 MPa. This specific SKU includes a male M5x0.8 threaded piston rod for direct load coupling and utilizes fluororubber (FKM) seals for enhanced thermal and oil resistance.
The 16 mm bore features an M5x0.8 air port and a 6 mm rod diameter. End-stop deceleration relies on fixed NBR bumpers rather than an adjustable air cushion, meaning external shock absorbers should be added for high-energy cycles. Because this configuration lacks the -S magnet option, it cannot support magnetic position sensing.
| Model | AirTAC SDA16X45BH Compact Cylinder | 16mm Bore |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø16 mm |
| Stroke | 45 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Rod end thread | M3×0.5 female / M5×0.8 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 50 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 101 N | 86 N |
| 0.7 MPa | 141 N | — |
| Max (@1.0 MPa) | 21 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 16 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Provides the 100.5 N extension stroke needed to push singulated circuit boards out of routing fixtures without stressing the 6 mm male rod.
Utilizes FKM seals to withstand ambient heat from sealing bars while maintaining a precise 45 mm stroke for card alignment.
Drives a metering valve in compact analytical equipment where axial space is restricted and consistent 86.4 N retract force is required.
When sizing this 16 mm bore actuator, evaluate your force margins carefully. Stepping down to the SDA12 reduces the push output to 56.5 N at 0.5 MPa, while stepping up to the SDA20 increases it to 157.1 N. For the SDA16X45BH, the safe working load is approximately 60 N (about 60% of the 100.5 N capacity), allowing a vertical lift of roughly 5.1 kg with a 2:1 safety margin. Confirm your ordering essentials: 16 mm bore, 45 mm stroke, M5x0.8 port, male rod thread (B), and FKM seals (H). Note that this cylinder cannot hold a load if air pressure drops; the piston will drift, requiring an external rod lock or pilot-operated check valve for fail-safe positioning.
Quick checklist
This 16 mm bore double-acting cylinder generates 100.5 N push and 86.4 N pull at 0.5 MPa, increasing to 140.7 N push and 121 N pull at 0.7 MPa. The theoretical maximum push is 21 kgf at 1.0 MPa. It operates between 0.15-1.0 MPa, handles speeds of 30-500 mm/s, and functions in temperatures from -20 to +70 C.
No, this specific SKU lacks the -S magnet option, so it cannot trigger AirTAC reed or electronic switches. Additionally, end-stop deceleration is handled by fixed NBR bumpers rather than an adjustable cushion, so you must control the approach speed externally for heavy or fast-moving loads.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.