The AirTAC AirTAC SDA20X10H Compact Cylinder | 20mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø20mm bore and 10mm stroke, M5×0.8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA20X10H is a double-acting, single-rod compact cylinder engineered for tight machinery footprints. Its riveted assembly reduces overall axial length, fitting easily where round-body units fail. This specific SKU features a fluororubber (FKM) seal for heightened oil and thermal resistance, delivering 157.1 N of push force at 0.5 MPa.
Equipped with an 8 mm piston rod and an M5x0.8 port, the unit operates at speeds between 30-500 mm/s. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this configuration lacks a piston magnet, so it cannot support magnetic sensing without the -S option.
| Model | AirTAC SDA20X10H Compact Cylinder | 20mm Bore |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø20 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Rod end thread | M4×0.7 female / M6×1.0 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 90 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 20 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Provides the short 10 mm clamping stroke needed to secure circuit boards during router cutting, utilizing the FKM seal to resist flux-contaminated environments.
Applies 157.1 N of precise extend force to close heated sealing jaws on pharmaceutical blister packs within confined machine frames.
Drives micro-liter fluid dispenser valves in analytical equipment where the 94 N safe working load prevents crushing delicate glass components.
When sizing this 20 mm bore actuator, consider stepping down to the SDA16 (100.5 N push @0.5 MPa) for lighter duties, or up to the SDA25 (245.4 N push @0.5 MPa) if your application demands greater thrust. Based on the 157.1 N output, the safe working load is roughly 94 N (60% capacity), allowing a vertical lift of about 8 kg with a 2:1 safety margin.
For ordering, confirm the 20 mm bore, 10 mm stroke, M5x0.8 port, FKM seal, and female M4x0.7 rod thread. Remember that a standard compact cylinder drifts if air pressure drops or the valve centers; the fixed bumper only slows the piston near stroke end. To hold a load securely without live pressure, integrate an external rod lock or pilot-operated check valve.
Quick checklist
This 20 mm bore double-acting cylinder generates 157.1 N push and 131.9 N pull at 0.5 MPa, and 219.9 N push at 0.7 MPa. The theoretical maximum push force is 32 kgf at 1.0 MPa. Operating pressure ranges from 0.15-1.0 MPa, with a proof pressure of 1.5 MPa.
No, this specific SKU does not include a piston magnet, so it cannot trigger AirTAC reed or electronic switches. You must select the -S option code to enable sensing. Additionally, end stops rely on a fixed NBR bumper, not an adjustable air cushion.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.