The AirTAC SDA20X30N Compact Cylinder | 20mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø20mm bore and 30mm stroke, M5×0.8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA20X30N is a double-acting single-rod compact cylinder engineered for tight machinery layouts. It provides 157.1 N of push force and 131.9 N of pull force at 0.5 MPa, utilizing a hard-anodized 20 mm bore and an 8 mm piston rod to deliver reliable linear motion.
Its short riveted body significantly reduces axial mounting depth compared to round-body alternatives, making it ideal for space-constrained footprints. The unit relies on a fixed NBR bumper at each end to decelerate the stroke, meaning it is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support magnetic sensing without upgrading to the -S variant.
| Model | AirTAC SDA20X30N Compact Cylinder | 20mm Bore |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø20 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Rod end thread | M4×0.7 female / M6×1.0 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 90 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 20 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Uses the 157.1 N extend force to push singulated circuit boards out of routing fixtures without damaging delicate traces.
Actuates a mechanical arm to tuck minor flaps on pharmaceutical cartons prior to sealing, fitting neatly into compact packaging frames.
Advances microplate trays a fixed 30 mm distance in analytical instruments where axial envelope space is highly restricted.
When sizing this actuator, evaluate your force requirements carefully. Stepping down to the SDA16 yields 100.5 N of push at 0.5 MPa, while moving up to the SDA25 provides 245.4 N, giving you clear boundaries for your application. To finalize your order, confirm the 20 mm bore, 30 mm stroke, M5x0.8 port, and the standard female M4x0.7 rod-end thread. Remember that a standard double-acting cylinder drifts when air pressure is lost or the valve is centered, so incorporate an external rod lock or pilot-operated check valve if your setup demands strict load holding.
Quick checklist
This double-acting cylinder generates 157.1 N push and 131.9 N pull at 0.5 MPa, and 219.9 N push at 0.7 MPa. The theoretical maximum push force is 32 kgf at 1.0 MPa. It operates on filtered air between 0.15-1.0 MPa, with a proof pressure of 1.5 MPa, and supports a speed range of 30-500 mm/s.
No, this specific SKU does not include a piston magnet, so it cannot trigger AirTAC reed or electronic switches. You would need to specify the -S option code to add a magnet for sensing. Additionally, end-stop deceleration is handled by a fixed NBR bumper, which is not an adjustable cushion.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.