The AirTAC SDA20X90SB Compact Cylinder | 20mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø20mm bore and 90mm stroke, M5×0.8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA20X90SB is a double-acting, single-rod compact cylinder engineered to deliver 157.1 N of push force and 131.9 N of pull force at 0.5 MPa. Its riveted assembly integrates the barrel, rear cover, piston, and rod to drastically reduce axial mounting depth, making it highly effective for machinery where a standard round-body unit would be too long. The bore is hard-anodized, and the piston relies on a two-way seal for consistent pneumatic performance.
This specific configuration includes a built-in piston magnet for position sensing alongside a male M6x1.0 threaded rod end for direct load coupling. Operating at speeds between 30 and 500 mm/s, the unit relies on a fixed NBR bumper at each end to decelerate the stroke. Because this 90 mm stroke approaches the 100 mm maximum standard limit for this bore, it is well-suited for extended reach tasks without requiring a custom order.
| Model | AirTAC SDA20X90SB Compact Cylinder | 20mm Bore |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø20 mm |
| Stroke | 90 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Rod end thread | M4×0.7 female / M6×1.0 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 90 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 20 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Provides the 157.1 N push force required to actuate the cutting head gantry on an electronics assembly line, utilizing the male M6 rod end for a rigid tool coupling.
Employs the 90 mm stroke to push lightweight cardboard cartons off a main conveyor belt, taking advantage of the short riveted body to fit within tight side-frame clearances.
When sizing this 20 mm bore, stepping down to the SDA16 yields 100.5 N of push force at 0.5 MPa, while stepping up to the SDA25 provides 245.4 N, allowing you to scale thrust precisely to your application. To confirm your ordering essentials for this model: specify the 20 mm bore, 90 mm stroke, M5x0.8 port, the required -S magnet, and the -B male-thread rod end. Keep in mind that a standard compact cylinder does not hold its position if air pressure is lost or the valve is centered; the piston will drift, and the fixed bumper only decelerates it near the stroke end rather than locking it. For applications requiring a held load, an external rod lock or a pilot-operated check valve is necessary.
Quick checklist
This double-acting cylinder generates a push force of 157.1 N and a pull force of 131.9 N at 0.5 MPa. At 0.7 MPa, the push force is 219.9 N. The theoretical maximum push force is 32 kgf at the maximum operating pressure of 1.0 MPa.
It uses a fixed NBR bumper at each end to decelerate the piston near the stroke limits, which is not an adjustable air cushion. If you need to hold a load vertically when air is lost, you must add an external rod lock or pilot-operated check valve, as the bumper is not a brake and the piston will drift.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.