The AirTAC AirTAC SDA32X15SB Compact Cylinder | 32mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø32mm bore and 15mm stroke, PT1/8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA32X15SB is a double-acting, single-rod compact cylinder engineered for tight axial spaces. It generates 402.1 N of push force and 345.6 N of pull force at 0.5 MPa, operating within a 30-500 mm/s speed range. The riveted unibody design significantly reduces overall mounting length compared to conventional round-body units, making it highly effective for shrinking machine footprints.
This specific configuration includes a built-in piston magnet (S) for direct mounting of AirTAC reed or electronic switches along the body grooves. It is equipped with a male M10x1.25 piston rod thread (B) for secure mechanical load coupling. End-stopping is handled by a fixed NBR bumper that decelerates the piston near stroke end rather than acting as an adjustable air cushion.
| Model | AirTAC SDA32X15SB Compact Cylinder | 32mm Bore |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø32 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M6×1.0 female / M10×1.25 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 120 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Secures printed circuit board panels during routing operations where the 402.1 N force and 15 mm stroke provide rigid holding without consuming valuable Z-axis height.
Actuates short folding mechanisms on packaging lines, utilizing the male M10x1.25 rod to push corrugated flaps into position prior to sealing.
Diverts small electronic parts on a conveyor using the integrated magnet and a solid-state switch to confirm the 15 mm extend position.
When sizing this unit, stepping down to the SDA25 yields 245.4 N of push force at 0.5 MPa, while stepping up to the SDA40 provides 628.3 N at the same pressure. Based on the 402.1 N output, the safe working load is approximately 241 N (about 60% capacity), translating to a vertical lift capability of roughly 20.5 kg with a 2:1 safety margin. To finalize your order, confirm the 32 mm bore, 15 mm stroke, PT1/8 port, male M10x1.25 rod, and the required magnetic switch. Note that this cylinder will drift and cannot hold a load if air pressure is lost or the valve is centered; maintaining vertical loads requires an external rod lock or pilot-operated check valve.
Quick checklist
This 32 mm bore double-acting cylinder provides 402.1 N push and 345.6 N pull at 0.5 MPa, 563 N push and 483.8 N pull at 0.7 MPa, and a theoretical maximum push of 82 kgf at 1.0 MPa.
It relies on a fixed NBR bumper at each end to decelerate the piston, which is not an adjustable air cushion. The included -S magnet allows you to track position using an AirTAC reed or electronic switch mounted in the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.