The AirTAC SDA40X20S Compact Cylinder | 40mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø40mm bore and 20mm stroke, PT1/8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.
The AirTAC SDA40X20S is a double-acting single-rod compact cylinder engineered to deliver 628.3 N of push force and 527.8 N of pull force at 0.5 MPa. Its riveted assembly merges the barrel, rear cover, piston, and rod into a highly abbreviated unit, drastically reducing axial mounting depth where a conventional round-body actuator would be too long. The 40 mm bore features a hard-anodized inner wall and a two-way piston seal for reliable low-friction operation.
Equipped with a built-in piston magnet (-S), this model supports position detection via an AirTAC reed or electronic switch housed in the grooves around the body. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, meaning external shock absorbers should be specified for high-energy cycles. The 16 mm rod terminates in a female M8x1.25 thread, and the pneumatic supply connects via a PT1/8 port.
| Model | AirTAC SDA40X20S Compact Cylinder | 40mm Bore |
|---|---|
| Series | SDA compact (thin) cylinder |
| Bore size | Ø40 mm |
| Stroke | 20 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod end thread | M8×1.25 female / M14×1.5 male (B) |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
| Max standard stroke | Up to 120 mm |
Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SDA | Compact (thin) double-acting cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×20 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| B | Male-thread piston rod (omit = female-thread rod). |
Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).
Secures aluminum workpieces in a machining center vise, utilizing the 628.3 N extend force to lock the part firmly against the locator stops during milling.
Deploys a 20 mm stroke to rapidly fold corrugated box flaps prior to tape sealing, where the short riveted body conserves valuable axial space on the conveyor frame.
Acts as a pneumatic stop pin on a pallet handling line, deploying the 16 mm rod to arrest incoming pallets before they enter the vertical lift station.
If your application requires less force, stepping down to the SDA32 yields 402.1 N at 0.5 MPa, while moving up to the SDA50 provides 981.7 N for heavier payloads. Keep in mind that a standard SDA body does not hold a load if air pressure drops or the valve is centered; the piston will drift, and the fixed bumper only decelerates near the stroke end. For suspended or vertical loads, an external rod lock or pilot-operated check valve is required.
When ordering, confirm the 40 mm bore, 20 mm stroke, PT1/8 porting, female M8x1.25 rod thread, and the -S magnet option for switch readiness.
Quick checklist
This double-acting 40 mm bore cylinder generates 628.3 N push and 527.8 N pull at 0.5 MPa, increasing to 879.6 N push and 738.9 N pull at 0.7 MPa. The theoretical maximum push force is 128 kgf at 1.0 MPa. It operates on filtered air between 0.15-1.0 MPa, with a proof pressure of 1.5 MPa, and supports a speed range of 30-500 mm/s.
It relies on a fixed NBR bumper at each end to decelerate the piston; it is not an adjustable air cushion, so high-speed applications may need external shock absorbers. The -S option includes a built-in magnet for use with AirTAC reed or electronic switches mounted in the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.