verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SDA Series · Compact Cylinder

AirTAC SDA40X80S Compact Cylinder | 40mm Bore

The AirTAC SDA40X80S Compact Cylinder | 40mm Bore is a genuine double-acting COMPACT (thin) air cylinder with a Ø40mm bore and 80mm stroke, PT1/8 air ports and a riveted short body that saves mounting depth. Sensor slots around the body accept magnetic switches for position sensing.

  • BoreØ40 mm
  • Stroke80 mm
  • Port sizePT1/8
  • Acting typeDouble acting
  • Rod threadM8×1.25 (F) / M14×1.5 (B)
  • CushionFixed NBR bumper (both ends)
$56.15 Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SDA40 stroke, mounting and version on one page All SDA40 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the AirTAC SDA40X80S Compact Cylinder | 40mm Bore

The AirTAC SDA40X80S is a double-acting, single-rod compact cylinder engineered to deliver 628.3 N of push force at 0.5 MPa. Its riveted body assembly merges the barrel, rear cover, piston, and rod into an axially short unit, saving valuable mounting depth where a traditional round-body actuator would not fit. The 40 mm bore features a hard-anodized inner wall and a 16 mm piston rod.

This specific configuration includes the S option, meaning it has a built-in piston magnet ready for AirTAC reed or electronic switches along the body grooves. End-of-travel deceleration relies on a fixed NBR bumper rather than an adjustable air cushion. Operating speeds span 30-500 mm/s, and the PT1/8 ports supply air efficiently to the two-way piston seal.

AirTAC SDA40X80S Compact Cylinder | 40mm Bore Technical Specifications

ModelAirTAC SDA40X80S Compact Cylinder | 40mm Bore
SeriesSDA compact (thin) cylinder
Bore sizeØ40 mm
Stroke80 mm
Acting typeDouble acting
Port sizePT1/8
Rod end threadM8×1.25 female / M14×1.5 male (B)
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C
Speed range30 – 500 mm/s
CushionFixed NBR bumper (both ends)
Max standard strokeUp to 120 mm

Specifications follow the official AirTAC SDA compact-cylinder datasheet. Confirm against the product label before installation. Port thread: PT (standard). Rod: female thread (blank) / male thread (B).

Theoretical Output Force (Ø40mm)

PressurePush forcePull force
0.5 MPa628 N528 N
0.7 MPa880 N—
Max (@1.0 MPa)128 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: AirTAC SDA40X80S Compact Cylinder | 40mm Bore

SDACompact (thin) double-acting cylinder series.
40Bore size in mm.
×80Stroke length in mm.
SBuilt-in magnet for magnetic-switch position sensing (omit = no magnet).
BMale-thread piston rod (omit = female-thread rod).

Thread: PT standard. Related SDA-family variants: SSA (single-acting push), STA (single-acting pull), SDAD (double rod), SDAJ (adjustable stroke), SDAT (duplex), SDAW (duplex-end).

Where the AirTAC SDA40X80S Compact Cylinder | 40mm Bore Is Used

packaging

Carton Erector Flaps

Provides the 628.3 N push stroke needed to fold heavy corrugated cardboard flaps on automated packaging lines at cycle rates within the 30-500 mm/s range.

conveyor_belt

Pallet Diverting Gate

Actuates a routing gate on a conveyor system, utilizing the 16 mm rod and compact riveted body to fit within tight side-frame clearances.

factory

Press Die Ejection

Pushes finished stamped parts out of a shallow die, relying on the fixed NBR bumper to absorb the end-stop impact without requiring external cushions.

Is the AirTAC SDA40X80S Compact Cylinder | 40mm Bore the Right Cylinder?

When sizing this model, stepping down to the SDA32 yields 402.1 N of push at 0.5 MPa, while stepping up to the SDA50 provides 981.7 N. Keep in mind a standard SDA does not hold its position if air pressure drops or the valve is centered; the piston will drift. For suspended loads, integrate an external rod lock or a pilot-operated check valve. To order, confirm the 40 mm bore, 80 mm stroke, PT1/8 port, female M8x1.25 rod thread, and the required S magnet option.

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Short-body depth vs. a round-body cylinder
  • ✓ Port/thread type (PT)
  • ✓ Magnet (S) for sensors?
  • ✓ Female (blank) or male (B) rod thread
  • ✓ Side load — avoid on a compact rod
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the short piston rod.
  • check Very long strokes are unsuitable for the compact body.
  • check Front/rear covers are riveted — do not dismantle.
  • check Installation by qualified personnel per AirTAC docs.

AirTAC SDA40X80S Compact Cylinder | 40mm Bore FAQ

At 0.5 MPa, the push force is 628.3 N and the pull force is 527.8 N. At 0.7 MPa, push is 879.6 N and pull is 738.9 N. The theoretical maximum push force is 128 kgf at 1.0 MPa, which is the maximum operating pressure.

No, it uses a fixed NBR bumper at each end to decelerate the stroke, which is not a field-adjustable air cushion. Additionally, it does not function as a lock; if air is lost, the piston drifts, so an external rod lock is needed to hold a load.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SDA Compact Cylinders

Request a Quote for AirTAC SDA40X80S Compact Cylinder | 40mm Bore

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SDA40X80S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.