
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X25-30S is a genuine double-acting COMPACT cylinder (Ø12mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 0 to 25 mm on the machine — no shims, no part change.
The AirTAC SDAJ12X25-30S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. Turning the M5x0.8 adjuster screw lets you dial the extend position from 0 to 25 mm directly on the machine, eliminating shims or part swaps during changeovers.
Its short riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit. The unit relies on a fixed NBR bumper at each end to decelerate the stroke, which is not an adjustable air cushion. Equipped with a built-in piston magnet, this version supports AirTAC reed or electronic switches for precise end-position sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X25-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø12 mm |
| Max stroke | 25 mm |
| Adjustable range | 0 – 25 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 42 N | 42 N |
| 0.7 MPa | 59 N | — |
| Max (@1.0 MPa) | 9 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 12 | Bore size in mm. |
| ×25 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Ideal for small machining fixtures where the extend stop must be fine-tuned between 0 and 25 mm to accommodate varying part tolerances without fabricating new spacers.
Provides a 56.5 N probe contact force at 0.5 MPa, allowing technicians to manually adjust the extension depth via the M5x0.8 screw for delicate testing sequences.
Fits into tight assembly stations to push small components, using the riveted body to save axial depth while adjusting the ejection length on the fly during product changeovers.
When sizing this 12 mm bore actuator, evaluate your neighbors: dropping down is not applicable at the bottom of the range, while stepping up to the SDAJ16 increases push force to 100.5 N at 0.5 MPa. Choose this model if your fixture requires frequent on-machine stroke tuning between 0 and 25 mm.
Confirm your parameters: 12 mm bore, 25 mm maximum stroke, 30 mm adjustment window, and an M5x0.8 air port. The -S magnet is present for switch sensing, and the rod-end thread is female M3x0.5. Note that a plain cylinder does not hold a load on air loss or valve centering; the fixed bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
The theoretical maximum push force is 12 kgf at 1.0 MPa.
The R (M5x0.8) screw shortens the extend stop by up to 30 mm, yielding a usable extend range of 0 to 25 mm. The screw acts as a mechanical stop and does not alter force. The included -S magnet works with AirTAC reed or electronic switches for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.