
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X30-10 is a genuine double-acting COMPACT cylinder (Ø12mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 20 to 30 mm on the machine — no shims, no part change.
The AirTAC SDAJ12X30-10 is a compact double-acting double-rod cylinder featuring an on-site extend stop. A front M5x0.8 adjuster screw lets you dial the outward travel down from the nominal 30 mm to a 20 mm minimum, removing the need for shims or part swaps during machine commissioning.
Built with a short riveted body, this unit saves axial mounting depth where round-body or profile alternatives will not fit. It uses a fixed NBR bumper at the ends to decelerate the piston rather than an adjustable air cushion. Note this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X30-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø12 mm |
| Max stroke | 30 mm |
| Adjustable range | 20 – 30 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 42 N | 42 N |
| 0.7 MPa | 59 N | — |
| Max (@1.0 MPa) | 9 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 12 | Bore size in mm. |
| ×30 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 20 to 30 mm clamping reach on delicate electronics fixtures without machining custom spacers.
Safely set a sensor or probe extension limit by turning the M5x0.8 screw during iterative testing.
Adjust the knock-out stroke on a compact assembly line to accommodate slight variations in component height.
When sizing this 12 mm bore actuator, consider the adjacent SDAJ16, which raises the 0.5 MPa push to 100.5 N for heavier resistance. Downward from 12 mm there is no smaller standard SDAJ, making this the most compact option available. The 10 mm adjustment window is highly useful for trial positioning or frequent changeovers. Confirm your requirements for bore, 30 mm maximum stroke, 10 mm window, M5x0.8 port, female rod thread, and no magnet.
A plain SDAJ does not hold a load if air pressure drops or the valve centers; the piston will drift. The fixed bumper only decelerates near the stroke end and the R screw is a mechanical stop, neither acts as a brake. For secure vertical load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 12 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with speeds of 30-500 mm/s.
The M5x0.8 R screw mechanically shortens the extend stop from 30 mm down to 20 mm. It does not alter the output force. The cylinder cannot hold a load on air loss; for load holding you need an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.