
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X40-20S is a genuine double-acting COMPACT cylinder (Ø12mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 20 to 40 mm on the machine — no shims, no part change.
The AirTAC SDAJ12X40-20S is a compact double-acting double-rod cylinder featuring an external M5x0.8 adjuster screw that lets you dial the extend stop anywhere between 20 and 40 mm directly on the machine. The short riveted body drastically reduces axial mounting depth, fitting into tight spaces where larger profile cylinders cannot. Equipped with a built-in magnet, this unit supports AirTAC reed or electronic switches for position confirmation.
End-of-travel deceleration relies on a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Operating speed spans 30-500 mm/s, and the M5x0.8 port matches the 12 mm bore specification. Keep side loading minimized on the 6 mm rod to ensure long seal life.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X40-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø12 mm |
| Max stroke | 40 mm |
| Adjustable range | 20 – 40 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 42 N | 42 N |
| 0.7 MPa | 59 N | — |
| Max (@1.0 MPa) | 9 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 12 | Bore size in mm. |
| ×40 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the extend stop from 20 to 40 mm to set exact clamping depth on delicate electronic components without machining new spacers.
Fine-tune the ejection stroke on a compact assembly line to accommodate varying product heights without changing out the entire actuator.
When sizing this 12 mm bore actuator, evaluate your force needs bidirectionally: stepping down is not an option as this is the smallest SDA bore, while moving up to the 16 mm bore raises the 0.5 MPa push to 100.5 N. Choose this model if your fixture requires on-site stroke tuning to hit a precise target without swapping shims.
Confirm your parameters: 12 mm bore, 40 mm max stroke, 20 mm adjust window, M5x0.8 port, female M3x0.5 rod thread, and the -S magnet option. Note that a plain cylinder does not hold a load if air pressure drops or the valve centers; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push is 79.2 N and pull is 59.4 N. The theoretical maximum push is 12 kgf at 1.0 MPa.
The M5x0.8 R screw mechanically shortens the extend stroke by up to 20 mm, yielding a usable 20-40 mm range without altering the output force. The included -S magnet works with AirTAC reed or electronic solid-state switches to confirm piston position.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.