
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X60-10S is a genuine double-acting COMPACT cylinder (Ø12mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 50 to 60 mm on the machine — no shims, no part change.
The AirTAC SDAJ12X60-10S is a compact double-acting double-rod cylinder featuring an external R (M5x0.8) adjustment screw. By turning this screw, you can dial the extend stop down from the 60mm maximum to any position between 50 and 60mm directly on the machine, eliminating the need for shims or part changes.
Designed for tight spaces, the short riveted body saves valuable axial mounting depth where round-body or profile alternatives will not fit. This specific model includes a built-in piston magnet (-S) for use with AirTAC reed or electronic switches. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Operating speed ranges from 30-500 mm/s.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ12X60-10S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø12 mm |
| Max stroke | 60 mm |
| Adjustable range | 50 – 60 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 42 N | 42 N |
| 0.7 MPa | 59 N | — |
| Max (@1.0 MPa) | 9 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 12 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Perfect for small machining fixtures where the 50-60mm extend stop is fine-tuned via the M5x0.8 screw to accommodate varying raw material thicknesses without swapping parts.
Suited for delicate electronics assembly lines where the extend position requires frequent adjustment during product changeovers, relying on the fixed NBR bumper for consistent end-stop absorption.
When sizing this 12mm bore actuator, consider your force requirements carefully. Conversely, there is no smaller standard bore below 12mm in this series, making this the baseline choice for ultra-light duties.
This model is ideal for operators needing on-site stroke tuning during commissioning or tooling changeovers. Verify your requirements for a 12mm bore, 60mm maximum stroke, 10mm adjust window, and M5x0.8 port. Note that a plain cylinder does not hold its load if air pressure is lost or the valve is centered; the piston will drift, and the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push force is 12 kgf at 1.0 MPa.
The R (M5x0.8) screw shortens the extend stroke by up to 10mm, giving a usable extend range of 50-60mm; retract remains full. The -S suffix indicates a built-in piston magnet compatible with AirTAC reed or electronic solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.