
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X10-10 is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 0 to 10 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X10-10 is a compact double-acting double-rod cylinder featuring an external M5x0.8 adjuster screw that dials the extend stop from 0 to 10 mm directly on your machine.
Its short riveted body drastically reduces axial mounting depth, fitting into tight spaces where bulkier alternatives fail. End-of-stroke deceleration relies on a fixed NBR bumper rather than an adjustable air cushion, and this specific SKU lacks a piston magnet, meaning it cannot host reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X10-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 10 mm |
| Adjustable range | 0 – 10 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×10 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop in 0-10 mm increments to set exact contact depth for seating small pins without crushing delicate housings.
Perfect for setup-heavy workholding where operators fine-tune the 100.5 N clamping force position on the fly during product changeovers.
Provides a compact footprint for test rigs needing precise 0-10 mm probe travel adjustments while maintaining a consistent 5.1 kg vertical lift margin.
Choose this unit if your fixture requires frequent on-site stroke tuning between 0 and 10 mm to perfect a pressing or clamping depth.
Confirm the bore size, 10 mm maximum stroke, 10 mm adjustment window, and M5x0.8 air port suit your pneumatic layout. Note that this configuration has no internal magnet, so position sensing is impossible here. Furthermore, a plain cylinder does not hold its load if air pressure drops or the valve is centered; the fixed bumper only decelerates the stroke end and acts as a mechanical stop, never a lock. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The M5x0.8 adjuster screw changes the stop position only, leaving these force values unchanged.
Turning the external R (M5x0.8) screw shortens the extend end-position by up to 10 mm, giving a usable extend range of 0 to 10 mm. This mechanism is strictly a mechanical stop, not a mid-stroke lock; the cylinder cannot hold a load if air is lost, and this specific SKU lacks the -S magnet required for reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.