
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X15-10S is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 5 to 15 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X15-10S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M5x0.8 adjuster screw lets you dial the extend position on-site between 5 and 15 mm, eliminating the need for shims or part swaps during machine commissioning.
Its short riveted body drastically reduces axial mounting depth, fitting into tight spaces where larger profile cylinders cannot. The unit includes a built-in piston magnet for AirTAC reed or electronic switches, while a fixed NBR bumper handles end-of-stroke deceleration.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X15-10S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 15 mm |
| Adjustable range | 5 – 15 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×15 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 5 to 15 mm extend stop during initial commissioning to find the perfect contact point for delicate probes without machining new spacers.
Eject small components weighing under 60 N safely, relying on the fixed NBR bumper to absorb the end shock while the magnet confirms retraction.
Quickly adjust the extend depth on-site when switching between slightly different product variants, saving axial space with its short riveted body.
When sizing this 16 mm bore actuator, evaluate your force requirements against its neighbours. Choose this specific model if your setup requires exact on-machine stroke tuning between 5 and 15 mm, and confirm your requirements for the M5x0.8 port, the 10 mm adjustment window, and the built-in magnet.
Remember that a plain compact cylinder does not hold a load if air pressure drops or the valve is centered; the piston will drift. The fixed NBR bumper only decelerates the stroke near its end and the R screw acts as a mechanical stop, not a brake. For secure load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve.
Quick checklist
It operates between 0.15 and 1.0 MPa at speeds of 30-500 mm/s.
The M5x0.8 R screw shortens the extend stroke by up to 10 mm, allowing you to set the end position anywhere between 5 and 15 mm. The included -S magnet enables position sensing with AirTAC reed or electronic switches, while the fixed NBR bumper decelerates the stroke end.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.