
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X20-20S is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 0 to 20 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X20-20S is a compact double-acting double-rod cylinder featuring an on-site extend stop. An external M5x0.8 adjuster screw lets you dial the forward end-position anywhere between 0 and 20 mm, eliminating the need for shims or part swaps during changeovers.
The short riveted body significantly reduces axial mounting depth, fitting into tight machine frames where round-body alternatives cannot. This unit includes a built-in piston magnet for AirTAC reed or electronic switches, while a fixed NBR bumper handles end-of-stroke deceleration. The adjuster is strictly a mechanical stop, not a mid-stroke lock or brake.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X20-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 20 mm |
| Adjustable range | 0 – 20 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×20 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the forward reach on the fly during product changeovers to push varying PCB widths out of a fixture without replacing the entire actuator assembly.
Set precise nozzle heights for chemical dispensing, relying on the fixed NBR bumper to decelerate the stroke end smoothly in compact laboratory automation frames.
Stepping down to the SDAJ12 yields 56.5 N, whereas moving up to the SDAJ20 provides 157.1 N. Choose this specific model if your fixture requires frequent trial positioning or exact forward tuning without swapping hardware.
Confirm the 16 mm bore, 20 mm maximum stroke, and 20 mm adjustment window suit your envelope. This variant ships with a built-in magnet (-S) for sensing, an M5x0.8 air port, and a female M3x0.5 rod-end thread. Remember that a standard compact cylinder does not hold a load if air pressure drops or the valve centers; the piston will drift. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 140.7 N and pull to 121 N. The theoretical maximum push is 21 kgf at 1.0 MPa.
The M5x0.8 R screw mechanically shortens the extend stop by up to 20 mm, yielding a usable forward range of 0 to 20 mm. The included -S magnet enables position detection using AirTAC reed or electronic switches. The screw does not alter force or lock the piston mid-stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.