
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X25-20 is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 5 to 25 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X25-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M5x0.8 adjuster screw lets you dial the extend end-position anywhere between 5 and 25 mm directly on the machine, eliminating the need for shims or part swaps during commissioning.
Its short riveted body saves valuable axial mounting depth where round-body or profile cylinders cannot fit. The bore uses an M5x0.8 air port and a 6 mm piston rod. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X25-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 25 mm |
| Adjustable range | 5 – 25 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×25 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 5-25 mm extend stop during initial commissioning of delicate pick-and-place jigs, ensuring the 6 mm rod contacts parts precisely without needing machined spacers.
Quickly readjust the extend endpoint on packaging lines when swapping product sizes, using the M5x0.8 screw to modify the stroke window on the fly instead of replacing the actuator.
If your application requires less force, dropping down to the SDAJ12 reduces the push to 56.5 N; conversely, stepping up to the SDAJ20 increases the push to 157.1 N.
This model is built for operators who need on-site stroke tuning to perfect a trial position or accommodate rapid tooling changeovers. Remember that a plain SDAJ does not hold position or load when air is lost or the valve is centred—the fixed bumper only decelerates near the end of travel. For load holding without live pressure, install an external rod lock or a pilot-operated check valve. Confirm your required 5-25 mm adjust window, M5x0.8 port, female M3x0.5 rod-end thread, and the absence of a magnet (no -S) before ordering.
Quick checklist
The theoretical maximum push is 21 kgf at 1.0 MPa. It operates between 0.15 and 1.0 MPa, with a proof pressure of 1.5 MPa, and runs at speeds from 30 to 500 mm/s.
The M5x0.8 R screw acts as a mechanical stop that shortens the extend stroke by up to 20 mm, allowing you to set the endpoint anywhere between 5 and 25 mm without altering the force. This specific SKU does not include a piston magnet; to use AirTAC reed or electronic switches, you must select the -S magnet option.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.