
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X25-30 is a genuine double-acting COMPACT cylinder (Ø16mm bore) whose extend end-position is set by an external M5×0.8 adjustment screw. You can dial the stroke anywhere from 0 to 25 mm on the machine — no shims, no part change.
The AirTAC SDAJ16X25-30 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M5x0.8 adjuster screw lets you dial the forward stroke from 0 to 25 mm directly on the machine without changing parts.
Its short riveted body minimizes axial mounting depth where larger profile designs will not fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. This specific SKU lacks a piston magnet, so it cannot support reed or electronic sensing without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ16X25-30 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø16 mm |
| Max stroke | 25 mm |
| Adjustable range | 0 – 25 mm |
| Adjuster thread (R) | M5×0.8 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M3×0.5 F / M5×0.8 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 86 N | 86 N |
| 0.7 MPa | 121 N | — |
| Max (@1.0 MPa) | 18 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 16 | Bore size in mm. |
| ×25 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dialing the extend stop down to 5 mm provides exact clamping force on delicate electronic components without redesigning the fixture.
Engineers can fine-tune the 0-25 mm forward travel during trial setups, finding the perfect engagement point before finalizing a machine build.
The compact riveted body fits into tight lab enclosures, while the mechanical stop ensures the probe tip touches the target without bottoming out violently.
Choose this unit if your fixture requires frequent on-site extend tuning within the 0-25 mm window.
Confirm your parameters: 16 mm bore, 25 mm maximum stroke, 30 mm adjustment window, and an M5x0.8 air port. This configuration ships without a magnet and has a female M3x0.5 rod-end thread. Remember that a standard cylinder does not hold position if air pressure drops or the valve centers; the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 140.7 N. The theoretical maximum push is 21 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a speed of 30-500 mm/s.
The M5x0.8 R screw mechanically shortens the extend stop, allowing you to set the forward travel anywhere from 0 to 25 mm. Retract remains full stroke. This SKU has no piston magnet and cannot accept a switch; you must select the -S option code to use reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.