
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X35-30B is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 5 to 35 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X35-30B is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M6x1.0 adjuster screw lets you dial the outward stroke down from the 35 mm maximum to as little as 5 mm directly on your machine, eliminating the need for shims or part swaps during changeovers.
This variant features a male M6x1.0 threaded piston rod end and lacks a piston magnet. The short riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X35-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 35 mm |
| Adjustable range | 5 – 35 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×35 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 5 to 35 mm via the M6x1.0 screw to accommodate different part heights on a machining line without swapping cylinders.
Use the 30 mm adjust window to fine-tune the locating pin extension in a fixture, finding the exact 8 kg vertical lift sweet spot before locking the screw.
Stepping down to the SDAJ16 yields 100.5 N, which may be insufficient for higher friction loads, while the SDAJ25 provides a sturdier 245.4 N if your fixture requires extra thrust. This model is specifically chosen when the exact extend position needs on-site tuning between 5 and 35 mm without disassembling the assembly.
Confirm your parameters before ordering: 20 mm bore, 35 mm maximum stroke, 30 mm adjust window, M5x0.8 air port, and a male M6x1.0 rod thread. Note that this SKU has no magnet, so position sensing is not possible without the -S option. Remember that the fixed NBR bumper only decelerates the stroke end; it does not act as a brake, and the cylinder will drift if air is lost unless you install a pilot-operated check valve.
Quick checklist
At 0.7 MPa the push increases to 219.9 N. The theoretical maximum push is 32 kgf at 1.0 MPa. The operational speed range is 30-500 mm/s.
No, this specific SKU does not include a piston magnet, so it cannot accept AirTAC reed or electronic switches. You would need to select the -S variant to enable sensing. The M6x1.0 screw only adjusts the mechanical extend stop between 5 and 35 mm; it does not alter the force or lock the piston mid-stroke.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.