
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X5-10S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 0 to 5 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X5-10S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M6x1.0 adjuster screw lets you dial the forward end-position from 0 to 5 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
Its short riveted body drastically reduces axial mounting depth, fitting easily into tight assemblies where round-body alternatives cannot. The unit relies on a fixed NBR bumper to absorb end-of-stroke shock rather than an adjustable air cushion. Equipped with a built-in piston magnet, this variant supports AirTAC reed or electronic switches for precise position sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X5-10S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 5 mm |
| Adjustable range | 0 – 5 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×5 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the 0-5 mm extend stop to compensate for material thickness variations during short-run changeovers, ensuring a precise 157.1 N clamp force without reprogramming the motion controller.
Fit the short riveted body into dense packaging machinery to push small parts precisely, using the external screw to fine-tune the ejection depth on the factory floor.
Utilize the built-in magnet with electronic switches to verify probe extension, adjusting the forward travel in 0-5 mm increments for delicate testing procedures.
When sizing this 20 mm bore actuator, evaluate your force requirements bidirectionally.
Choose this configuration if your fixture requires on-site stroke tuning between 0 and 5 mm. Confirm your setup needs an M5x0.8 port, a female M4x0.7 rod-end thread, and the -S magnet for switch integration. Note that a plain cylinder drifts when air is lost or a valve centers; the fixed bumper only decelerates the stroke end and does not function as a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 219.9 N and pull to 184.7 N. The theoretical maximum push force is 32 kgf at 1.0 MPa.
The M6x1.0 R screw shortens the extend stroke by up to 10 mm, allowing you to set the forward stop anywhere between 0 and 5 mm. The retract stroke remains full. The included -S magnet works with AirTAC reed or electronic switches for position detection.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.