verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SDAJ Series · Adjustable-Stroke Compact Cylinder

Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S

The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 30 to 50 mm on the machine — no shims, no part change.

  • BoreØ20 mm
  • Max stroke50 mm
  • Adjustable range30–50 mm
  • Adjuster threadM6×1.0
  • Port sizeM5×0.8
  • CushionFixed NBR bumper (both ends)
$38.84 $46.34Save 16% Standard model — ready in 3-5 business days to process and dispatch
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
Compare every SDAJ20 stroke, mounting and version on one page All SDAJ20 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7-8 h

About the Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S

The AirTAC SDAJ20X50-20S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M6x1.0) screw, you can dial the forward stroke from 30 to 50 mm directly on your machine without changing parts.

Its short riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit. The unit relies on a fixed NBR bumper to decelerate the stroke end rather than an adjustable air cushion. Because the -S option is present, a built-in piston magnet enables position detection with AirTAC reed or electronic switches.

Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S Technical Specifications

ModelAirtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S
SeriesSDAJ compact adjustable-stroke cylinder
Bore sizeØ20 mm
Max stroke50 mm
Adjustable range30 – 50 mm
Adjuster thread (R)M6×1.0
Port sizeM5×0.8
Acting typeDouble acting
Rod end threadM4×0.7 F / M6×1.0 male (B)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C
Speed range30 – 500 mm/s
CushionFixed NBR bumper (both ends)

The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.

Theoretical Output Force (Ø20mm)

PressurePush forcePull force
0.5 MPa132 N132 N
0.7 MPa185 N—
Max (@1.0 MPa)27 kgf

SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.

Model Code: Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S

SDAJCompact double-acting cylinder with adjustable stroke.
20Bore size in mm.
×50Maximum stroke length in mm.
-20Adjustable window (10/20/30/40/50/75/100 mm).
S / BS = magnet; B = male-thread rod (both optional).

Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).

Where the Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S Is Used

precision_manufacturing

Tooling Changeover

Dial the extend stop from 30 to 50 mm via the M6x1.0 screw to accommodate varied part heights during machine setup without fabricating new spacers.

science

Trial Positioning

Use the reed or electronic switch feedback alongside the 20 mm window to find the exact extension point for delicate sensor calibration before locking the stop.

Is the Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S the Right Cylinder?

When sizing this 20 mm bore actuator, evaluate your force requirements bidirectionally. Choose this unit if your fixture requires on-site stroke tuning between 30 and 50 mm.

Confirm your specifications: 20 mm bore, 50 mm max stroke, 20 mm adjust window, M5x0.8 port, built-in magnet, and female M4x0.7 rod thread. Note that a plain cylinder does not hold its load on air loss or valve centring; the piston drifts and the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or pilot-operated check valve.

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Target position within 30–50 mm
  • ✓ Force at your working pressure
  • ✓ Access to reach the R adjuster
  • ✓ Magnet (S) for sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Lock the M6×1.0 adjuster after setting the stroke.
  • check Avoid side load on the piston rod.
  • check Front/rear covers are riveted — do not dismantle.
  • check Installation by qualified personnel per AirTAC docs.

Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S FAQ

The theoretical maximum push is 32 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and speed ranges from 30-500 mm/s.

The R (M6x1.0) screw shortens the extend stop by up to 20 mm, allowing usable extensions between 30 and 50 mm. The -S option includes a built-in piston magnet for AirTAC reed or electronic switches. The screw sets the stop position and does not alter force or act as a mid-stroke lock.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Standard models are processed and dispatched in 3-5 business days.

bolt

Fast Reply

Most inquiries answered within 7-8 hours.

Related AirTAC SDAJ Cylinders

Request a Quote for Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X50-20S

Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.

Thank you. We received your request for SDAJ20X50-20S and will confirm price, stock and lead time — usually within 7-8 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.