
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X55-40S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 15 to 55 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X55-40S is a compact double-acting double-rod cylinder featuring an external M6x1.0 adjuster screw that dials the extend stop directly on your machine. You can set the outward travel anywhere between 15 and 55 mm without swapping shims or parts, while the retract stroke remains full length.
This 20 mm bore unit carries a built-in piston magnet (-S) for direct mounting of AirTAC reed or electronic switches along the body grooves. The short riveted body drastically cuts axial mounting depth where a larger profile cylinder will not fit. End-of-travel deceleration relies on a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X55-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 55 mm |
| Adjustable range | 15 – 55 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×55 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 15 to 55 mm extend stop on a machining fixture to compensate for cutter wear, avoiding part changes while keeping the short riveted body within tight axial clearances.
Leverage the built-in magnet with an electronic switch to verify the end position of a testing probe, tweaking the outward reach safely for delicate sample contact up to 55 mm.
This SDAJ20X55-40S sits perfectly in the middle, pushing 157.1 N at 0.5 MPa.
Choose this specific model if your fixture requires frequent changeovers or trial positioning within the 15 to 55 mm extend band. Confirm the 55 mm maximum stroke, 40 mm adjustment window, M5x0.8 port, and the female M4x0.7 rod-end thread suit your tooling. Note that the fixed bumper only decelerates the stroke end; a plain cylinder does not hold a load if air pressure drops or the valve centers. For suspended loads, integrate an external rod lock or pilot-operated check valve.
Quick checklist
At 0.7 MPa the push increases to 219.9 N and the pull to 184.7 N. The theoretical maximum push is 32 kgf at 1.0 MPa.
Turning the R (M6x1.0) adjuster screw shortens the extend stroke by up to 40 mm, allowing you to set the outward stop anywhere between 15 and 55 mm. The included -S magnet enables position detection using AirTAC reed or solid-state electronic switches mounted in the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.