
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X60-30B is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 30 to 60 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X60-30B is a compact double-acting double-rod cylinder featuring an on-site adjustable extend stop. By turning the external M6x1.0 adjuster screw, you can dial the forward end-position anywhere between 30 and 60 mm without swapping shims or parts.
This thin riveted-body design saves valuable axial mounting depth where larger profile or round-body units will not fit. It comes equipped with a male M6x1.0 piston rod thread (M4x0.7 female is standard) and an M5x0.8 air port. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X60-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 60 mm |
| Adjustable range | 30 – 60 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 30 to 60 mm via the M6x1.0 screw during machine changeovers to accommodate varying part widths without fabricating new spacers.
Set the exact extend endpoint during initial fixture commissioning, safely testing positions within the 30 mm window before locking down the final mechanical stop.
When sizing this unit, evaluate your force requirements bidirectionally. Choose this specific model if your fixture requires frequent changeovers or trial positioning within the 30 to 60 mm forward range.
Confirm the bore (20 mm), maximum stroke (60 mm), and 30 mm adjustment window suit your cycle time, keeping in mind the operational speed range is 30-500 mm/s. The male M6x1.0 rod thread and M5x0.8 port are fixed to this bore size. Crucially, a standard cylinder does not hold a load if air pressure drops or the valve centers; the piston will drift. For suspended or vertical loads, you must integrate an external rod lock or a pilot-operated check valve, as the fixed NBR bumper only decelerates near the end of travel and provides no braking function.
Quick checklist
At 0.7 MPa, push increases to 219.9 N and pull to 184.7 N. The theoretical maximum push is 32 kgf at 1.0 MPa.
Turning the R (M6x1.0) external screw shortens the extend stroke by up to 30 mm, allowing an on-machine range of 30 to 60 mm. The -B code denotes a male M6x1.0 piston rod thread instead of the default female M4x0.7. This SKU has no magnet (-S) and cannot support switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.