
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X65-50S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 15 to 65 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X65-50S is a compact double-acting double-rod cylinder featuring an external M6x1.0 adjuster screw that dials the extend stop from 15 to 65 mm directly on your machine. This on-site tunability eliminates the need for shims or part swaps during setup and changeovers.
Built with a short riveted body, this unit saves valuable axial mounting depth where round-body or profile cylinders will not fit. The bore-fixed M5x0.8 air port keeps the footprint minimal, while the integrated piston magnet supports AirTAC reed or electronic switches for precise end-position detection. End shock is managed by a fixed NBR bumper, which decelerates the stroke but is not an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X65-50S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 65 mm |
| Adjustable range | 15 – 65 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×65 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 15 and 65 mm via the M6x1.0 screw during prototype runs to find the exact contact point for delicate 8 kg test loads.
Quickly reset the stroke length on packaging lines for different carton sizes without swapping out the entire actuator assembly or adding shims.
Utilize the short riveted body to fit within tight axial spaces while pushing with 157.1 N at 0.5 MPa to seat small electronic connectors.
Choose this specific model if your fixture requires frequent trial positioning or variable extend endpoints within its 15 to 65 mm window.
Confirm the 20 mm bore, 65 mm maximum stroke, 50 mm adjust window, M5x0.8 port, and the built-in magnet (S) for your mounting arrangement. Note that a plain compact cylinder does not hold a load when air is lost or the valve is centred; the piston drifts and the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 32 kgf at 1.0 MPa. The external stop screw does not alter these force values.
The M6x1.0 R screw shortens the extend stroke by up to 50 mm, giving an adjustable range of 15 to 65 mm. The retract stroke remains full. The built-in S magnet works with AirTAC reed or electronic switches for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.