
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X70-10SB is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 60 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X70-10SB is a compact double-acting double-rod cylinder featuring an external M6x1.0 adjuster screw that dials the extend stop from 60 to 70 mm directly on your machine. The short riveted body minimizes axial mounting depth, fitting easily where larger profile cylinders cannot.
This specific configuration includes a built-in piston magnet (-S) for AirTAC reed or electronic switches and a male M6x1.0 threaded rod end (-B) instead of the default female M4x0.7. End-of-travel shock is managed solely by a fixed NBR bumper, which decelerates the piston near the end of the stroke but is not an adjustable air cushion. Operating speed ranges from 30 to 500 mm/s.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X70-10SB |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 70 mm |
| Adjustable range | 60 – 70 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the 10 mm extend window during machine changeovers to set precise 60-70 mm probe depths without swapping shims or cylinder bodies.
Leverage the built-in magnet and electronic switches to verify exact extend stops during R&D trials, adjusting the M6x1.0 screw for iterative testing.
Choose this model if your fixture requires on-site extend tuning between 60 and 70 mm, a male M6x1.0 rod thread, and switch sensing.
Confirm your parameters: 20 mm bore, 70 mm maximum stroke, 10 mm adjustment window, M5x0.8 port, -S magnet for reed or electronic sensing, and -B male rod. Remember that a plain cylinder does not hold position or load when air is lost or the valve is centered; the fixed bumper only decelerates near the end, and the R screw is a mechanical stop, not a lock. For load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 219.9 N and pull to 184.7 N. The theoretical maximum push is 32 kgf at 1.0 MPa. The adjustment screw does not alter these force values.
Turning the external R (M6x1.0) screw shortens the extend stroke by up to 10 mm, allowing you to set the end position anywhere between 60 and 70 mm. The -S code indicates a built-in piston magnet compatible with AirTAC reed or electronic solid-state switches for end-of-stroke sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.