
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X70-20S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 50 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X70-20S is a compact double-acting double-rod cylinder featuring an external M6x1.0 adjuster screw that lets you dial the extend stop down from 70 mm to 50 mm directly on the machine. The short riveted body significantly reduces axial mounting depth, fitting easily into tight assemblies where longer cylinders cannot.
This unit includes a built-in piston magnet (-S) for position sensing with AirTAC reed or electronic switches. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Operating speed ranges from 30 to 500 mm/s across a 0.15 to 1.0 MPa pressure range.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X70-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 70 mm |
| Adjustable range | 50 – 70 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 70 mm down to 50 mm during fixture changeovers to accommodate varying part heights without machining new spacers.
Use the 20 mm adjust window to fine-tune the crush depth on carton sealing jaws, ensuring a perfect seal before locking the M6x1.0 screw in place.
Choose this specific model if your fixture requires frequent on-machine stroke tuning between 50 and 70 mm without swapping shims or parts.
Confirm your requirements for the 20 mm bore, 70 mm maximum stroke, 20 mm adjust window, and M5x0.8 port. This unit has the -S magnet for sensing and a female M4x0.7 rod-end thread. Remember that a plain cylinder does not hold a load when air is lost or the valve is centred; the fixed bumper only decelerates near the end of the stroke. For load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 219.9 N and pull to 184.7 N. The theoretical maximum push is 32 kgf at 1.0 MPa. The adjustable stop does not alter these force values.
The external M6x1.0 adjuster screw shortens the extend stroke by up to 20 mm, allowing you to set the end position anywhere between 50 mm and 70 mm. The retract stroke remains full length. The -S suffix indicates a built-in piston magnet for use with AirTAC reed or electronic solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.