
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X70-50B is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 20 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X70-50B is a compact double-acting double-rod cylinder featuring an external extend stop. An M6x1.0 adjuster screw lets you dial the outward stroke anywhere between 20 and 70 mm directly on your equipment, eliminating the need for shims or part swaps.
This variant features a male M6x1.0 piston rod thread and lacks a piston magnet. Its short riveted body saves valuable axial mounting depth where larger profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X70-50B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 70 mm |
| Adjustable range | 20 – 70 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Ideal for trial positioning on prototype jigs where the exact extend point between 20 and 70 mm must be dialed in iteratively without disassembling the fixture.
Provides adjustable reach for packaging lines running varied box heights, allowing operators to tweak the 157.1 N extend thrust contact point during rapid changeovers.
Delivers a consistent push for seating small bearings, with the mechanical stop ensuring the part bottoms out correctly rather than relying solely on pneumatic pressure.
When sizing this actuator, evaluate your force requirements bidirectionally. This specific SKU includes the -B option for a male-threaded M6x1.0 rod end and has no -S magnet, meaning it cannot accept reed or electronic switches. Confirm your required 20 to 70 mm adjustment window, M5x0.8 port size, and 70 mm maximum stroke before ordering.
Remember that a standard compact cylinder does not hold position or maintain a load if air pressure drops or the directional valve is centered. The piston will drift, and the fixed NBR bumper only decelerates the stroke near its ends—it is not a locking brake. For suspended or vertical loads that must remain secure without live pressure, integrate an external rod lock or a pilot-operated check valve into your pneumatic circuit.
Quick checklist
At 0.7 MPa, push increases to 219.9 N and pull to 184.7 N. The theoretical maximum push force is 32 kgf at 1.0 MPa.
Turning the R (M6x1.0) screw mechanically shortens the extend end position by up to 50 mm, giving a usable outward stroke range of 20 to 70 mm. It sets the physical stop and does not alter the pneumatic force. Note that this SKU lacks the -S magnet option, so magnetic switches cannot be used.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.