
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X85-30S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 55 to 85 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X85-30S is a compact double-acting double-rod cylinder featuring an on-site adjustable extend stop. An external M6x1.0 adjuster screw lets you dial the forward stroke anywhere between 55 and 85 mm without changing parts.
This variant includes a built-in piston magnet (-S) for direct mounting of AirTAC reed or electronic solid-state switches along the body grooves. The short riveted body saves valuable axial depth in tight machinery, while a fixed NBR bumper decelerates the piston at the extremes. Operating speed spans 30-500 mm/s across a 0.15 to 1.0 MPa pressure range.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X85-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 85 mm |
| Adjustable range | 55 – 85 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×85 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact extend position between 55 and 85 mm during quick tooling swaps, avoiding the need to machine custom spacers for varying part heights.
Fine-tune the mechanical stop on carton folding mechanisms to accommodate different box profiles on the fly, ensuring crisp folds without reprogramming the motion controller.
Safely test end-of-stroke contact points in R&D rigs by threading the M6x1.0 adjuster screw inward, limiting impact force during trial cycles.
When sizing this 20 mm bore unit, evaluate your force needs bidirectionally. Choose this specific unit if your fixture requires frequent changeovers or trial positioning within the 55-85 mm extend window.
Confirm the 20 mm bore, 85 mm maximum stroke, 30 mm adjust window, and M5x0.8 port. The -S code denotes the internal magnet for sensing, and the female M4x0.7 rod thread suits standard clevis attachments. Note that a plain cylinder drifts when air is lost or the valve is centered; the fixed bumper only decelerates near the end of travel and is not a lock. For secure load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 219.9 N and pull to 184.7 N. The theoretical maximum push force is 32 kgf at 1.0 MPa.
Turning the external R (M6x1.0) screw shortens the extend stop by up to 30 mm, yielding a usable forward travel of 55 to 85 mm. The retract stroke remains full length. The built-in magnet (-S) allows you to track position using AirTAC reed or electronic solid-state switches mounted in the body grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.