
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X85-75S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 10 to 85 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X85-75S is a compact double-acting double-rod cylinder featuring an external M6x1.0 adjustment screw that lets you dial the extend stop anywhere between 10 and 85 mm directly on your machine. Retract travel stays at the full 85 mm length. This thin riveted-body design saves valuable axial mounting depth where larger profile or round-body units will not fit.
Equipped with a built-in piston magnet (-S), this unit supports AirTAC reed or electronic solid-state switches mounted directly into the body sensor grooves. End-of-stroke energy is managed by a fixed NBR bumper that decelerates the piston, though it is not an adjustable air cushion. Operating speed ranges from 30 to 500 mm/s across a 0.15 to 1.0 MPa pressure range.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X85-75S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 85 mm |
| Adjustable range | 10 – 85 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×85 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 10 to 85 mm during prototype runs to find the exact 94 N safe contact point without swapping shims or cylinders.
Turn the M6x1.0 adjuster to shift the extend endpoint for different product lengths, leveraging the 30-500 mm/s speed range for rapid cycling.
Choose this specific model when your fixture requires frequent on-machine stroke tuning during setup or changeovers.
Confirm the 20 mm bore, 85 mm maximum stroke, and 75 mm adjustable window suit your spatial envelope, noting the M5x0.8 port and female M4x0.7 rod-end thread. The included magnet enables position sensing with reed or electronic switches. Remember that a plain cylinder does not hold a load when air is lost or the valve is centered; the fixed bumper only decelerates near the end of travel and the R screw is a mechanical stop, not a lock. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The adjustment screw does not alter these force values.
The external M6x1.0 screw shortens the extend stroke by up to 75 mm, yielding a usable 10 to 85 mm range while retract remains full. The -S suffix denotes a built-in piston magnet for tracking position with AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.