
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X90-10S is a genuine double-acting COMPACT cylinder (Ø20mm bore) whose extend end-position is set by an external M6×1.0 adjustment screw. You can dial the stroke anywhere from 80 to 90 mm on the machine — no shims, no part change.
The AirTAC SDAJ20X90-10S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. An M6x1.0 adjuster screw lets you dial the forward end-position anywhere between 80 and 90 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
Built with a short riveted body, this unit saves axial mounting depth where round-body or profile cylinders cannot fit. The 20 mm bore uses an M5x0.8 air port and an 8 mm rod. End-of-travel deceleration is handled by a fixed NBR bumper at each end, which absorbs shock but is not an adjustable air cushion. The included -S piston magnet supports position sensing using AirTAC reed or electronic switches mounted in the body grooves.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ20X90-10S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø20 mm |
| Max stroke | 90 mm |
| Adjustable range | 80 – 90 mm |
| Adjuster thread (R) | M6×1.0 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M4×0.7 F / M6×1.0 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 132 N | 132 N |
| 0.7 MPa | 185 N | — |
| Max (@1.0 MPa) | 27 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 20 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the M6 screw to find the exact 80-90 mm extend point for prototype parts before locking down the final stop, avoiding repeated teardowns.
Fine-tune the forward travel of an 8 mm rod to gently push a product against a gauge, relying on the fixed NBR bumper to absorb the final impact.
When sizing this 20 mm bore actuator, evaluate your force needs bidirectionally. Stepping up, the SDAJ25 yields 245.4 N at 0.5 MPa, offering a sturdier alternative if your payload approaches the upper limit.
This specific configuration includes a built-in magnet (S) for electronic or reed sensing and a female M4x0.7 rod-end thread. It is tailored for lines requiring frequent on-machine stroke tuning within the 10 mm window. Remember that a plain compact cylinder does not hold position if air pressure drops or the valve is centered; the fixed NBR bumper only decelerates near the end of travel. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 32 kgf at 1.0 MPa.
The M6x1.0 R screw shortens the extend stroke by up to 10 mm, giving a usable forward range of 80 to 90 mm without changing force. The -S suffix indicates a built-in piston magnet for use with AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.