
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X100-20S is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 80 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X100-20S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. Turning the R (M8x1.25) screw lets you dial the forward end-position anywhere between 80 and 100 mm directly on the machine, eliminating the need for shims or part swaps. Retract remains full length.
The short riveted body saves valuable axial mounting depth where round-body or profile cylinders will not fit. End-of-travel deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. This specific unit includes the -S option, meaning a built-in piston magnet is present for position sensing using AirTAC reed or electronic switches.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X100-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 100 mm |
| Adjustable range | 80 – 100 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the mechanical stop on-site to accommodate varying box heights, maintaining consistent force across the 20 mm adjustment window.
When sizing this 25 mm bore actuator, evaluate your force requirements both ways.
Choose this configuration if your application requires frequent on-site stroke tuning during setup or changeovers. Confirm the 100 mm maximum stroke, 20 mm adjustment window, and M5x0.8 port. The -S magnet enables switch integration, while the female M5x0.8 rod-end thread suits standard mounting. Remember that a plain cylinder does not hold position if air pressure drops or the valve centers; the fixed bumper only decelerates near the end of travel and is not a lock. For load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. It operates between 0.15 and 1.0 MPa, with a proof pressure of 1.5 MPa, and runs at speeds from 30 to 500 mm/s.
The external R (M8x1.25) screw mechanically shortens the extend stroke by up to 20 mm, giving a usable range of 80 to 100 mm. It does not alter the force. The cylinder does not hold its load if air is lost or the valve is centered; for load holding, you must use an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.