
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X100-75 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 25 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X100-75 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M8x1.25) screw, you can shorten the forward stroke on-site, dialling the rod end anywhere between 25 and 100 mm without changing parts or adding shims. The retract motion remains full length.
Its short riveted body drastically saves axial mounting depth where a larger profile cylinder will not fit. End-of-trock deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches; you would need the -S variant for position sensing.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X100-75 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 100 mm |
| Adjustable range | 25 – 100 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 25 to 100 mm via the M8x1.25 screw to accommodate different part heights on a machining line without fabricating new spacers.
Set the exact 12.5 kg vertical lift limit during prototype assembly, locking the mechanical stop exactly where the component seats without reprogramming pressure.
When sizing this 25 mm bore actuator, evaluate your force needs against its neighbours. Choose this unit if your fixture requires frequent on-machine stroke tuning between 25 and 100 mm during changeovers.
Confirm your required bore, 100 mm max stroke, 75 mm adjust window, and M5x0.8 port. The female rod-end thread is M5x0.8. Remember that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end, and the adjuster is a mechanical stop, not a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. The adjuster does not change these values.
The external R (M8x1.25) screw mechanically shortens the extend stroke by up to 75 mm, allowing the rod to stop anywhere between 25 and 100 mm. This specific SKU has no magnet and cannot take a switch; you must specify the -S option to use reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.