
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X85-75 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 10 to 85 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X85-75 is a double-acting compact cylinder featuring an external adjustable extend stop. An M8x1.25 adjuster screw lets you dial the rod extension from 10 to 85 mm directly on the machine, eliminating the need for shims or part swaps during setup.
Built with a short riveted body, this unit saves axial mounting depth where round-body or profile cylinders will not fit. It uses a fixed NBR bumper at each end to decelerate the stroke, rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot accept reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X85-75 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 85 mm |
| Adjustable range | 10 – 85 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 75 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×85 | Maximum stroke length in mm. |
| -75 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 10 to 85 mm during product family swaps to set new push depths without machining new spacers.
Fine-tune the mechanical stop during line commissioning to find the exact 12.5 kg vertical lift point before locking the M8x1.25 screw.
When sizing this actuator, evaluate your force requirements bidirectionally. Choose this specific model if your application requires frequent on-machine stroke tuning across a wide 75 mm window.
Verify your parameters: 25 mm bore, 85 mm maximum stroke, 75 mm adjust window, and an M5x0.8 port. The rod end features a female M5x0.8 thread. Keep in mind that a plain SDAJ does not hold position or load when air is lost or the valve is centred; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa.
Turning the M8x1.25 screw shortens the extend stop anywhere between 10 and 85 mm; it sets the stop position and does not alter force. It is not a mid-stroke lock, and the cylinder cannot hold a load on air loss without an external rod lock or pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.