
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X120-40B is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 80 to 120 mm on the machine — no shims, no part change.
The AirTAC SDAJ32X120-40B is a double-acting compact cylinder featuring an external M10x1.25 R-thread adjuster screw. This mechanism lets you dial the extend stop down from the 120mm maximum to any point between 80 and 120mm directly at the machine, eliminating the need for shims or part swaps during setup.
Built with a short riveted body, this unit saves axial mounting depth where round-body or profile cylinders cannot fit. It carries a male M10x1.25 piston rod thread (option B) on a 12mm diameter rod, and operates on a PT1/8 port. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot host reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X120-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 120 mm |
| Adjustable range | 80 – 120 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×120 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the pusher stroke on-site during product changeovers, ensuring the male M10x1.25 rod retracts packages accurately without needing to swap out the entire cylinder body.
Set precise upper travel limits for a 20.5kg vertical lift mechanism, relying on the fixed NBR bumper to absorb the end shock as the load reaches its designated height.
When sizing this 32mm bore, evaluate your thrust requirements both ways. Choose this specific unit if your fixture requires on-site stroke tuning across an 80 to 120mm window, and confirm your bore, 120mm max stroke, 40mm adjust window, PT1/8 port, male M10x1.25 rod, and lack of magnet match the design criteria.
Keep in mind that a standard compact cylinder does not hold its load when air is lost or the directional valve centers. The piston will drift, and the fixed NBR bumper only decelerates the stroke near the end rather than acting as a mechanical lock. If your application demands positive load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve into the pneumatic circuit.
Quick checklist
At 0.7MPa the push increases to 563N. The theoretical maximum push is 82kgf at 1.0MPa. Operating pressure spans 0.15-1.0MPa, with a proof pressure of 1.5MPa and a speed range of 30-500mm/s.
The external M10x1.25 screw mechanically shortens the extend stop by up to 40mm, allowing usable travel between 80 and 120mm. It is a hard stop only and does not function as a mid-stroke lock; the piston will drift if air pressure is removed.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.