
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X70-30B is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 40 to 70 mm on the machine — no shims, no part change.
The AirTAC SDAJ32X70-30B is a compact double-acting double-rod cylinder featuring an external M10x1.25 adjustment screw that dials the extend stop from 40 to 70 mm directly on your machine. The short riveted body significantly reduces axial mounting depth, fitting easily into tight machinery envelopes where larger profile or round-body units cannot.
This specific configuration includes a male M10x1.25 piston rod thread for direct threaded mounting. End-of-stroke deceleration is handled by a fixed NBR bumper at each end, which absorbs shock but is not an adjustable air cushion. Operating speed spans 30-500 mm/s, and the unit accepts standard AirTAC compact-cylinder accessories.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X70-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 70 mm |
| Adjustable range | 40 – 70 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×70 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 40 and 70 mm during die swaps to accommodate varying part heights without fabricating new mechanical shims.
Sweep the male M10x1.25 rod through the 30 mm adjustment range to find the exact contact position for new sensor brackets before finalizing a design.
Choose this model if your fixture requires on-site stroke tuning to perfect a pressing or clamping position without machining new spacers.
Verify your requirements against these specs: 32 mm bore, 70 mm maximum stroke, 30 mm adjust window, PT1/8 air port, and a male M10x1.25 rod thread (option B). Note that this SKU lacks a piston magnet (-S), so it cannot host reed or electronic switches. Furthermore, a plain cylinder does not hold position or load upon air loss; the fixed bumper only decelerates near the end of travel. For suspended or vertical loads, install an external rod lock or pilot-operated check valve.
Quick checklist
At 0.7 MPa the push increases to 563 N and the pull to 483.8 N. The theoretical maximum push is 82 kgf at 1.0 MPa.
Turning the external R (M10x1.25) screw mechanically shortens the extend end-position from 70 mm down to 40 mm. It acts purely as a stop and does not alter force. It is not a mid-stroke lock; the cylinder will drift if air pressure is lost, so use an external rod lock for load holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.