
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X75-30B is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 45 to 75 mm on the machine — no shims, no part change.
The AirTAC SDAJ32X75-30B is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M10x1.25) screw, you can dial the extend position anywhere between 45 and 75 mm directly on the machine without shims or part changes.
This variant features a male M10x1.25 piston rod thread and a PT1/8 air port. The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet and therefore cannot support reed or electronic switches.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X75-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 75 mm |
| Adjustable range | 45 – 75 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the 45 to 75 mm extend stop on the fly to accommodate raw material thickness variations without reprogramming the machine controller.
Swap product formats quickly by turning the M10x1.25 adjuster screw to reposition the male rod end, saving setup time between production batches.
Establish precise ejection distances during prototype runs by testing different extend endpoints within the 30 mm window before locking down the final mechanical stop.
When sizing this 32 mm bore, consider the neighbouring capacities at 0.5 MPa.
Choose this male-rod (-B) model if your tooling requires an M10x1.25 threaded attachment point and you need on-site stroke tuning for frequent changeovers. Remember that a plain cylinder does not hold its load if air pressure drops or the valve is centered; the piston will drift and the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve. Confirm your requirements for the 32 mm bore, 75 mm maximum stroke, 30 mm adjustment window, PT1/8 port, and lack of a magnet.
Quick checklist
At 0.7 MPa, push increases to 563 N and pull to 483.8 N. The theoretical maximum push force is 82 kgf at 1.0 MPa.
The R (M10x1.25) screw mechanically shortens the extend stroke by up to 30 mm, allowing usable endpoints between 45 and 75 mm. This specific SKU does not have a piston magnet, so it cannot accept reed or electronic switches; you would need the -S variant for sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.