
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X80-40B is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 40 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ32X80-40B is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M10x1.25) screw, you can dial the forward end-position anywhere between 40 and 80 mm directly on the machine, eliminating the need for shims or part swaps.
This variant features a male M10x1.25 piston rod thread and lacks a piston magnet, meaning it cannot accept magnetic switches without upgrading to the -S option. The short riveted body significantly reduces axial mounting depth compared to round-body alternatives, fitting easily into tight assemblies. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion or a load-holding brake.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X80-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 80 mm |
| Adjustable range | 40 – 80 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 40 and 80 mm to accommodate different raw material lengths on a single machining fixture without swapping physical stop blocks.
Fine-tune the forming depth during initial setup by turning the R screw, preventing over-travel on delicate workpieces before locking down the final position.
Choose this specific model if your setup requires on-site stroke tuning to accommodate multiple product formats without changing hardware.
Confirm the following specifications match your requirements: 32 mm bore, 80 mm maximum stroke, 40 mm adjustment window, PT1/8 air port, and a male M10x1.25 rod thread. Note that a plain cylinder does not hold its load if air pressure is lost or the valve is centered; the piston will drift. For load holding without live pressure, you must integrate an external rod lock or a pilot-operated check valve.
Quick checklist
At 0.7 MPa, push increases to 563 N and pull to 483.8 N. The theoretical maximum push is 82 kgf at 1.0 MPa. Operating pressure ranges from 0.15 to 1.0 MPa, with a speed of 30-500 mm/s.
The external M10x1.25 adjuster screw mechanically shortens the extend stroke by up to 40 mm, allowing you to set the forward stop anywhere between 40 mm and 80 mm. This SKU does not include a piston magnet, so it cannot accept magnetic switches; you would need the -S variant to use reed or electronic sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.