Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10 is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 80 to 90 mm on the machine — no shims, no part change.
- BoreØ32 mm
- Max stroke90 mm
- Adjustable range80–90 mm
- Adjuster threadM10×1.25
- Port sizePT1/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10
The AirTAC SDAJ32X90-10 is a double-acting compact cylinder featuring an external adjustable extend stop. An M10x1.25 adjuster screw lets you dial the outward stroke down from the 90 mm maximum to 80 mm directly at the machine, eliminating the need for shims or part swaps during setup.
Built with a short riveted body, this unit saves axial mounting depth where round-body or profile cylinders cannot fit. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot accept magnetic switches; add the -S option if position sensing is required.
Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10 Technical Specifications
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 90 mm |
| Adjustable range | 80 – 90 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10 Is Used
Tooling Calibration
Dial in the exact extend position between 80 and 90 mm during initial tooling setup without machining custom spacers.
Trial Positioning
Fine-tune the outward reach of a testing probe in 1 mm increments via the M10x1.25 screw until the optimal contact point is found.
Is the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10 the Right Cylinder?
Stepping down to the SDAJ25 yields 245.4 N, whereas moving up to the SDAJ40 provides 628.3 N.
This model is specified with a 90 mm maximum stroke, a 10 mm adjustment window, a PT1/8 port, a female M6x1.0 rod-end thread, and no magnet. It is ideal for operators who need on-site stroke tuning to perfect a motion sequence. Remember that a plain cylinder does not hold its load if air pressure drops or the valve centers; the bumper only decelerates near the end of travel. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 80–90 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M10×1.25 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10 FAQ
The theoretical maximum push is 82 kgf at 1.0 MPa.
Turning the external R (M10x1.25) screw mechanically shortens the extend stop, allowing the outward stroke to be set anywhere from 80 to 90 mm. This adjustment changes the end position only and does not alter the cylinder's output force.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.