Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 80 to 90 mm on the machine — no shims, no part change.
- BoreØ32 mm
- Max stroke90 mm
- Adjustable range80–90 mm
- Adjuster threadM10×1.25
- Port sizePT1/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B
The AirTAC SDAJ32X90-10B is a compact double-acting cylinder featuring an external extend stop. An M10x1.25 adjuster screw lets you dial the outward stroke from 80 to 90 mm directly on the machine, eliminating the need for shims or part swaps.
This variant uses a male M10x1.25 piston rod and a PT1/8 port. Its short riveted body saves axial mounting depth where round-body alternatives will not fit. End shock is managed solely by a fixed NBR bumper, which decelerates the stroke but is not an adjustable air cushion. Note this SKU lacks a piston magnet, so magnetic sensing is not supported.
Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B Technical Specifications
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 90 mm |
| Adjustable range | 80 – 90 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B Is Used
Tooling Setup
Dial the 10 mm extend window to precisely seat 32 mm bore clamps during initial fixture commissioning.
Changeover Lines
Fine-tune the 80 to 90 mm outward stop to accommodate different part heights on rapid format changeovers.
Is the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B the Right Cylinder?
This model suits operators needing on-site extend tuning between 80 and 90 mm. Remember that a plain cylinder drifts when air is lost or a valve centers; the fixed bumper only decelerates near the end of travel and does not act as a lock. For load holding without live pressure, install an external rod lock or pilot-operated check valve. Confirm your bore, stroke, 10 mm window, PT1/8 port, male M10 rod, and lack of magnet before ordering.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 80–90 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M10×1.25 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B FAQ
The theoretical maximum is 82 kgf at 1.0 MPa.
Turning the R (M10x1.25) screw shortens the extend stop from the 90 mm maximum down to 80 mm. It sets the end position without changing force, and it is not a mid-stroke lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-10B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.