Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50 is a genuine double-acting COMPACT cylinder (Ø32mm bore) whose extend end-position is set by an external M10×1.25 adjustment screw. You can dial the stroke anywhere from 40 to 90 mm on the machine — no shims, no part change.
- BoreØ32 mm
- Max stroke90 mm
- Adjustable range40–90 mm
- Adjuster threadM10×1.25
- Port sizePT1/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50
The AirTAC SDAJ32X90-50 is a double-acting compact cylinder featuring a 32mm bore and an external adjustable extend stop. By turning the R (M10x1.25) screw, you can dial the extend end-position anywhere between 40 and 90 mm directly on your machine, avoiding part swaps or shims.
The short riveted body saves valuable axial mounting depth where a round-body or profile cylinder will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Note that this specific SKU lacks a piston magnet, so it cannot support reed or electronic switches; you would need the -S variant for position sensing.
Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50 Technical Specifications
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Max stroke | 90 mm |
| Adjustable range | 40 – 90 mm |
| Adjuster thread (R) | M10×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M6×1.0 F / M10×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50 Is Used
Machining Clamp Depth
Dial the extend stop from 40 to 90 mm to accommodate varying raw stock thicknesses on a milling fixture without machining new spacers.
Changeover Adjustment
Speed up product family changeovers by turning the M10x1.25 screw to reposition the 402.1 N clamping point on the fly.
Trial Positioning
Iterate on prototype assembly press depths safely, using the mechanical stop to prevent over-travel before finalizing the cycle.
Is the Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50 the Right Cylinder?
Choose this model if your fixture requires frequent on-machine stroke tuning between 40 and 90 mm during changeovers. Confirm your setup needs a 32mm bore, 90mm max stroke, 50mm adjust window, PT1/8 port, female M6x1.0 rod thread, and no magnet. Remember that a plain cylinder does not hold its load on air loss or valve centering—the piston drifts and the fixed bumper only decelerates near the end. For a held load, specify an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 40–90 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M10×1.25 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50 FAQ
The external M10x1.25 screw shortens the extend stroke by up to 50 mm, allowing usable travel between 40 and 90 mm. It is a mechanical stop, not a mid-stroke lock; the cylinder will drift if air is lost, so use an external rod lock for load holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ32X90-50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.