
The AirTAC SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X100-20 is a genuine double-acting COMPACT cylinder (Ø40mm bore) whose extend end-position is set by an external M12×1.25 adjustment screw. You can dial the stroke anywhere from 80 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ40X100-20 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M12x1.25) screw, you shorten the outward stroke on-site across an 80 to 100 mm window, eliminating the need for shims or part swaps during machine commissioning.
Designed with a short riveted body, this unit saves substantial axial mounting depth where a larger profile cylinder would fail to fit. End-of-travel energy is managed solely by a fixed NBR bumper, which decelerates the piston near the end of the stroke but is not an adjustable air cushion or a locking brake. Operating pressure spans 0.15 to 1.0 MPa, and the piston speed ranges from 30 to 500 mm/s.
| Model | Airtac SDAJ32~40 Adjustable Super Slim Cylinder SDAJ40X100-20 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Max stroke | 100 mm |
| Adjustable range | 80 – 100 mm |
| Adjuster thread (R) | M12×1.25 |
| Port size | PT1/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M8×1.25 F / M14×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial in the exact 80-100 mm extend position during CNC changeovers to clamp raw castings securely without machining custom spacer blocks.
Set repeatable trial extension endpoints for sensor calibration rigs, leveraging the fixed NBR bumper to decelerate the probe safely at the end of travel.
Choose this specific model if your fixture setup requires frequent trial positioning or on-machine stroke tuning within the 80 to 100 mm range.
Confirm the bore, 100 mm maximum stroke, 20 mm adjustment window, and PT1/8 air port match your pneumatic layout. This SKU lacks the -S magnet option, so it cannot accept AirTAC reed or electronic switches; add the -S variant if your control system requires position sensing. Remember that a standard cylinder does not hold a load if air pressure drops or the valve is centered—you must integrate an external rod lock or pilot-operated check valve for secure load holding.
Quick checklist
At 0.7 MPa, push increases to 879.6 N and pull to 738.9 N. The theoretical maximum push is 128 kgf at 1.0 MPa.
Turning the external M12x1.25 adjuster screw shortens the extend stroke by up to 20 mm, allowing you to set the outward endpoint anywhere between 80 and 100 mm. The retract stroke remains full, and the screw acts only as a mechanical stop, not a mid-stroke lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.